View EPF10K130E_6657079.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

altera corporation 1 flex 10ke embedded programmable logic family august 1999, ver. 2.02 data sheet a-ds-f10ke-02.02 features... n embedded programmable logic devices (plds), providing system-on-a-programmable-chip tm integration in a single device enhanced embedded array for implementing megafunctions such as efficient memory and specialized logic functions preliminary information dual-port capability with up to 16-bit width per embedded array block (eab) logic array for general logic functions n high density 30,000 to 200,000 typical gates (see tables 1 and 2 ) up to 98,304 ram bits; 4,096 bits per eab, all of which can be used without reducing logic capacity n system-level features multivolt tm i/o pins can drive or be driven by 2.5-v, 3.3-v, or 5.0-v devices low power consumption bidirectional i/o performance ( t su and t co ) up to 250 mhz fully compliant with the peripheral component interconnect special interest group (pci sig) pci local bus specification, revision 2.2 for 3.3-v operation at 33 mhz or 66 mhz -1 speed grade devices are compliant with pci local bus specification, revision 2.2 , for 5.0-v operation built-in joint test action group (jtag) boundary-scan test (bst) circuitry compliant with ieee std. 1149.1-1990, available without consuming additional device logic f for information on 5.0-v flex 10k or 3.3-v flex 10ka devices, see the flex 10k embedded programmable logic family data sheet . table 1. flex 10ke device features feature epf10k30e epf10k50e epf10k50s epf10k100b typical gates (1) 30,000 50,000 100,000 maximum system gates 119,000 199,000 158,000 logic elements (les) 1,728 2,880 4,992 eabs 6 10 12 total ram bits 24,576 40,960 24,576 maximum user i/o pins 220 254 191
2 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation n ote to tables: (1) the embedded ieee std. 1149.1 jtag circuitry adds up to 31,250 gates in addition to the listed typical or maximum system gates. . ..and more features fabricated on an advanced process and operate with a 2.5-v internal supply voltage in-circuit reconfigurability (i cr) via external configuration d evices, intelligent controller, or jtag port clocklock tm and clockboost tm options for reduced clock delay/skew and clock multiplication built-in low-skew clock distribution trees 100 % functional testing of all devices; test vectors or scan chains are not required pull-up on i/o pins before and during configuratio n n f lexible interconnect fasttrack interconnect c ontinuous routing structure for fast, predictable interconnect delays dedicated carry chain that implements arithmetic functions such as fast adders, counters, and comparators (automatically used by software tools and megaf unctions) dedicated cascade chain that implements high-speed, high-fan-in logic functions (automatically used by software tools and megafunctions) tri-state emulation that implements internal tri-state buses up to six global clock signals and four global clear signals n powerful i/o pins individual tri-state output enable control for each pin open-drain option on each i/o pin programmable output slew-rate control to reduce switching noise clamp to v cc io user-selectable on a pin-by-pin basis supports hot-socketing table 2. flex 10ke device features feature epf10k100e EPF10K130E epf10k200e epf10k200s typical gates (1) 100,000 130,000 200,000 maximum system g ates 2 57,000 3 42,000 5 13,000 logic elements (les) 4,992 6,656 9,984 eabs 12 16 24 total ram bits 49,152 65,536 98,304 maximum user i/o pins 338 413 470
altera corporation 3 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet n software design support and automatic place-and-route provided by altera? max+p l us i i development system for windows-based pcs and sun sparcstation, hp 9000 series 700/800, and ibm risc system/6000 workstations , and the quartus tm development system for windows-based pcs and sun sparcstation and hp 9000 series 700 workstations n flexible package options available in a variety of packages with 144 to 672 pins, including the innovative fineline bga tm packages (see tables 3 and 4 ) sameframe tm pin c ompatibility w ith flex 10ka and f lex 10ke devices a cross a range of device densities and pin counts n additional design entry and simulation support provided by edif 2 0 0 and 3 0 0 netlist files, library of parameterized modules (lpm), designware components, verilog hdl, vhdl, and other interfaces to popular eda tools from manufacturers such as cadence, exemplar logic, mentor graphics, orcad, synopsys, synplicity, veribest, and viewlogic notes: (1) contact altera customer marketing for up-to-date information on package availability. (2) flex 10ke device package types include thin quad flat pack (tqfp), plastic quad flat pack (pqfp), pin-grid array (pga), and ball-grid array (bga) packages. (3) devices in the same package are pin-compatible, although some devices have more i/o pins than others. when planning device migration, use the i/o pins that are common to all devices. the max+plus ii software versions 9.1 and higher provide features to help designers use only the common pins. (4) this option will be supported with a 484-pin fineline bga package. by using sameframe pin migration, all fineline bga packages are pin-compatible. for example, a board can be designed to support 256-pin, 484-pin, and 672-pin fineline bga packages. the quartus and max+plus ii software automatically avoids conflicting pins when future migration is set. table 3. flex 10ke package op tions & i/o pin count notes (1) , (2) , (3) device 144-pin tqfp 208-pin pqfp 240-pin pqfp rqfp 256-pin fineline bga 356-pin bga 484-pin fineline bga 599-pin pga 600-pin bga 672-pin fineline bga epf10k30 e 102 147 176 220 220 (4) epf10k 50e 102 147 189 191 220 254 254 (4) epf10k 50s 102 147 189 191 220 254 254 (4) epf10k 100b 147 189 191 epf10k 100e 147 189 191 274 338 338 (4) epf10k 130e 186 274 369 424 413 epf10k 200e 470 470 470 epf10k 200s 182 274 369 470 470 470
4 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation gen eral description altera flex 10ke devices are e nhance d versions o f the flex 10k device family. based on reconfigurable cmos sram elements, the flexible logic element matrix (flex) architecture incorporates all features necessary to implement common gate array megafunctions. with up to 200,000 gates, flex 10ke devices p rovide t he density, speed, and features to integrate entire systems, including multiple 32-bit buses, into a single device. the ability to reconfigure flex 10ke devices enables 1 00 % test ing p rior to shipment and allows the designer to focus on simulation and design verification. flex 10ke reconfigurability eliminates inventory management for gate array designs and generation of test vectors for fault coverage. table 5 shows flex 10ke performance for some common designs. all performance values w ere obtained with synopsys designware or lpm functions. special design techniques are not required to implement the applications; the designer simply infers or instantiates a function in a verilog hdl, vhdl, altera hardware description language (ahdl), or schematic design file. table 4. flex 10ke package sizes device 144- pin tqfp 208-pin pqfp 240-pin pqfp rqfp 256-pin fineline bga 356- pin bga 484-pin fineline bga 599-pin pga 600- pin bga 672-pin fineline bga pitch (mm) 0.50 0.50 0.50 1.0 1.27 1.0 1.27 1.0 area (mm 2 ) 484 936 1,197 289 1,225 529 3,904 2,025 729 length width (mm mm) 22 22 30.6 30.6 34.6 34.6 17 17 35 35 23 23 62.5 62.5 45 45 27 27
altera corporation 5 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet notes: (1) this application uses combinatorial inputs and outputs. (2) this application uses registered inputs and outputs. table 6 shows flex 10ke performance for more complex designs. these designs are available as altera meg acore functions. table 5. flex 10ke pe rformance application resources used performance units les eabs speed grade -1 -2 -3 16-bit loadable counter 1 6 0 200 18 8 128 mhz 16-bit accumulator 16 0 200 1 88 128 mhz 16-to-1 multiplexer (1) 10 0 3.2 4.3 5.5 ns 16-bit multiplier with 3-stage pipeline (2) 544 0 9 3 86 64 mhz 256 16 ram read cycle speed (2) 0 1 212 1 81 1 31 mhz 256 16 ram write cycle speed (2) 0 1 142 1 28 94 mhz table 6. flex 10ke pe rformance for complex designs application les used performance units speed grade -1 - 2 - 3 16-bit, 8-tap parallel finite impulse response (fir) filter 420 185 175 122 msps 8-bit, 512-point fast fourier transform (fft) function 1,8 54 47.4 57.8 76.5 ? 100 82 62 mhz a16450 universal asynchronous receiver/transmitter (uart) 342 66 57 44 mhz
6 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation similar to the flex 10ke architecture, embedded gate arrays are the fastest-growing segment of the gate array market. as with standard gate arrays, embedded gate arrays implement general logic in a conventional ?ea-of-gates?architecture. additionally, embedded gate arrays have dedicated die areas for implementing large, specialized functions. by embedding functions in silicon, e mbedded gate arrays r educe d ie area and increase s peed when compared to standard gate arrays. while embedded megafunctions typically cannot be customized, flex 10ke devices are programmable, providing the designer with full control over embedded megafunctions and general logic while facilitating iterative design changes during debugging. each flex 10ke device contains an embedded array and a logic array. the embedded array is used to implement a variety of memory functions or complex logic functions, such as digital signal processing (dsp), wide data-path manipulation, microcontroller applications, and data- transformation functions. the logic array performs the same function as the sea-of-gates in the gate array and i s used to implement general logic, such as counters, adders, state machines, and multiplexers. the combination of embedded and logic arrays provides the high performance and high density of embedded gate arrays, enabling designers to implement an entire system on a single device. flex 10ke devices are configured at system power-up with data stored in an altera serial co nfiguration de vice or provided by a system controller. altera offers the epc1, epc2, and epc1441 co nfiguration devices, which configure flex 10ke devices via a serial data stream. configuration data can also be downloaded from system ram or via t he altera bitb laster tm , byte blaster tm , or byte blastermv tm d ownload cable s . (the byteblaster cable is obsolete and is replaced by the byteblastermv cable, which can program and configure 2.5-v, 3.3-v, and 5.0-v devices.) after a flex 10ke device has been configured, it can be reconfigured in- circuit by resetting the device and loading new data. because reconfiguration requires less than 276 ms, real-time changes can be made during system operation. flex 10ke devices contain an i nterface that permits microprocessors to configure flex 10ke devices serially or in parallel, and synchronously or asynchronously. the interface also enables microprocessors to treat a flex 10ke device as memory and configure it b y writing to a virtual memory location, making it e asy t o reconfigure the device. f for more information, see t he following documents: n configuration devices for apex & flex devices data sheet n bitblaster serial download cable data sheet n byteblastermv parallel port download cable data sheet
altera corporation 7 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet flex 10ke devices are supported by the quartus and max+plus ii development systems, which are integrated packages that offer schematic, text (including ahdl), a nd waveform design entry , c ompilation and logic synthesis , f ull simulation and worst-case timing analysis , a nd device configuration. the quartus and max+plus ii software provides edif 2 0 0 and 3 0 0, lpm, vhdl, verilog hdl, and other interfaces for additional design entry and simulation support from other industry-standard pc- and unix workstation-based eda tools. the quartus and max+plus ii software works easily with common gate array eda tools for synthesis and simulation. for example, the max+plus ii software can generate verilog hdl files for simulation with tools such as cadence verilog-xl. additionally, the quartus and max+plus ii software contains eda libraries that use device-specific features such as carry chains w hich are used for fast counter and arithmetic functions. for instance, the synopsys design compiler library supplied with the quartus and max+plus ii development systems include designware functions that are optimized for the flex 10ke architecture. the max+p l us i i development system runs on windows-based pcs and sun sparcstation, hp 9000 series 700/800, and ibm risc system/6000 workstations , and the quartus development system runs on windows- based pcs , and sun sparcstation and hp 9000 series 700 workstations. f see t he max+plus ii programmable logic development system & software data sheet and the quartus programmable logic development system & software data sheet f or more information. functi onal description each flex 10ke device contains an enhanced embedded array to implement memory and specialized logic functions, and a logic array to implement general logic. the embedded array consists of a series of eabs. when implementing memory functions, each eab provides 4,096 bits, which can be used to create ram, rom, dual-port ram, or first-in first-out (fifo) functions. when implementing logic, each eab can contribute 100 to 600 gates towards complex logic functions, such as multipliers, microcontrollers, state machines, and dsp functions. eabs can be used independently, or multiple eabs can be combined to implement larger functions.
8 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation the logic array consists of logic array blocks (labs). each lab contains eight les and a local interconnect. an le consists of a 4- input look-up table (lut), a programmable flipflop, and dedicated signal paths for carry and cascade functions. the eight les can be used to create medium-sized blocks of logic?uch as 8-bit counters, address decoders, or state machines?r combined across labs to create larger logic blocks. each lab represents about 96 usable gates of logic. signal inter connections within flex 10ke devices (as well as to and fr om device pins) ar e pr ovided by the fastt rack inter connect r outing str uctur e, which is a se ries of fast, continuous r ow and column channels that r un the entir e length and width of the device. each i/o pin is fed by an i/o element (ioe) located at the end of each row and column of the fasttrack interconnect routing structure. each ioe contains a bidirectional i/o buffer and a flipflop that can be used as either an output or input register to feed input, output, or bidirectional signals. when used with a dedicated clock pin, these registers provide exceptional performance. as inputs, they provide setup times as low as 2.5 n s and hold times of 0 ns . as outputs, these registers provide clock-to-output times as low as 3.7 n s. ioes pr ovide a variety of featur es, such as jt ag bst support, slew-rate contr ol, tri-state buf fers, and open-drain outputs.
altera corporation 9 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet figure 1 shows a block diagram of the flex 10ke architecture. each group of les is combined into an lab; groups of labs a re arranged into rows and columns. each row also contains a single eab. the labs and eabs are interconnected by the fasttrack interconnect routing structure. ioes are located at the end of each row and column of the fastt rack inter connect r outing str uctur e . figure 1. flex 10ke device bloc k diagram flex 10ke devices provide six dedicated inputs that drive the flipflops? control inputs and ensure the efficient distribution of high-speed, low- skew (less than 1.5 ns) control signals. these signals use dedicated routing channels that provide shorter delays and lower skews than the fasttrack interconnect routing structure. four of the dedicated inputs drive four global signals. these four global signals can also be driven by internal logic, providing an ideal solution for a clock divider or an internally generated asynchronous clear signal that clears many registers in the device. i / o e l e m e n t ( i o e ) l o g i c a r r a y b l o c k ( l a b ) r o w i n t e r c o n n e c t i o e i o e i o e i o e i o e i o e i o e l o c a l i n t e r c o n n e c t i o e i o e i o e i o e i o e i o e i o e i o e i o e i o e l o g i c e l e m e n t ( l e ) c o l u m n i n t e r c o n n e c t i o e e a b e a b l o g i c a r r a y i o e i o e i o e i o e i o e i o e e m b e d d e d a r r a y b l o c k ( e a b ) e m b e d d e d a r r a y i o e i o e l o g i c a r r a y i o e i o e
10 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation embed ded array block the eab is a flexible block of ram with registers on the input and output ports that is used to implement common gate array megafunctions. because it is large and flexible, the eab is suitable for functions such as multipliers, vector scalars, and error correction circuits. these functions can be combined in applications such as digital filters and microcontrollers. logic functions are implemented by programming the eab with a read- only pattern during configuration, thereby creating a large l ut. with luts, combinatorial functions are implemented by looking up the results, rather than by computing them. this implementation of combinatorial functions can be faster than using algorithms implemented in general logic, a performance advantage that is further enhanced by the fast access times of eabs. the large capacity of eabs enables designers to implement complex functions in one logic level without the routing delays associated with linked les or field-programmable gate array (fpga) ram blocks. for example, a single eab can implement a ny function with 8 inputs and 16 outputs. p arameterized functions such as lpm functions can take advantage of the eab automatically. the flex 10ke eab provides advantages over fpgas, w hich implement on-board ram as arrays of small, distributed ram blocks. these small fpga ram blocks must be connected together to make r am blocks of manageable size. the ram blocks are connected together using multiplexers implemented with more logic blocks. these extra multiplexers cause extra delay, which slows down the ram block. fpga ram blocks are also prone to routing problems because small blocks of ram must be connected together to make larger blocks. in contrast, eabs can be used to implement large, dedicated blocks of ram that eliminate these timing and routing concerns. the flex 10ke enhanced eab adds dual-port capability to the existing eab structure. the dual-port structure is ideal for fifo buffers with one or two clocks. the flex 10ke eab can also support up to 16-bit-wide ram blocks and is backward-compatible with any design containing flex 10k eabs. the flex 10ke eab can act in dual-port or single-port mode. when in dual-port mode, separate clocks may be used for eab read and write sections, which allows the eab to be written and read at different rates. it also has separate synchronous clock enable signals for the eab read and write sections, which allow independent control of these sections.
altera corporation 11 preliminary in f ormation flex 10ke embe d ded p r ogrammable logic f ami l y data sheet the e ab can also be used for bidirectional, dual-port memory app l ications where two ports read or write simultaneously. to implement this t ype of dual-port memory, two eabs are used to support two sim u ltaneous read or writes. a lternatively, one clock and clock enable can be used to control the input registers of the eab, while a different clock and clock enable control the output registers (see figure 2 ). figure 2. flex 10ke device in dual-port ram mode notes (1) , (2) notes: (1) all registers can be asynchronously cleared by eab local interconnect signals, global signals, or the chip-wide reset. (2) the epf10k100b device does not offer dual-port ram mode. (3) epf10k30e and epf10k50e devices have 88 eab local interconnect channels; epf10k100e, EPF10K130E , and epf10k200e devices have 104 eab local interconnect channels. column interconnect eab local interconnect (3) dedicated clocks 24 d ena q d ena q d ena q d ena q d ena q data[ ] rdaddress[ ] wraddress[ ] ram/rom 256 16 512 8 1,024 4 2,048 2 data in read address write address read enable write enable data out 4, 8, 16, 32 4, 8, 16, 32 outclocken inclocken inclock outclock d ena q write pulse generator rden wren multiplexers allow read address and read enable registers to be clocked by inclock or outclock signals. row interconnect 4, 8 dedicated inputs & global signals
12 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation the eab can also use altera megafunctions to implement dual-port ram applications where both ports can read or write, as shown in figure 3 . figure 3. flex 10ke eab in dual-port ram mode p o r t a p o r t b a d d r e s s _ a [ ] a d d r e s s _ b [ ] d a t a _ a [ ] d a t a _ b [ ] w e _ a w e _ b c l k e n a _ a c l k e n a _ b c l o c k a c l o c k b
altera corporation 13 preliminary in f ormation flex 10ke embe d ded p r ogrammable logic f ami l y data sheet t he flex 10ke eab can be used in a single-port mode, which is useful for backward-compatibility with flex 10k designs (see figure 4 ). figure 4. flex 10ke device in single-port ram mode note: (1) epf10k30e, epf10k50e, and epf10k50s devices have 88 eab local interconnect channels; epf10k100e, epf10k100b, EPF10K130E, epf10k200e, and epf10k200 s devices have 104 eab local interconnect channels. eabs can be used to implement synchronous ram, which is easier to use than asynchronous ram. a circuit using asynchronous ram must generate the ram write enable signal, while ensuring that its data and address signals meet setup and hold time specifications relative to the write enable s ignal. in contrast, the eab? synchronous ram generates its own write enable signal and is self-timed with respect to the input or write clock. a circuit using the eab? self-timed ram must only meet the setup and hold time specifications of the global clock. c o l u m n i n t e r c o n n e c t e a b l o c a l i n t e r c o n n e c t ( 1 ) d e d i c a t e d i n p u t s & g l o b a l s i g n a l s d q d q r a m / r o m 2 5 6 1 6 5 1 2 8 1 , 0 2 4 4 2 , 0 4 8 2 d a t a i n a d d r e s s w r i t e e n a b l e d a t a o u t 4 , 8 , 1 6 , 3 2 4 , 8 , 1 6 , 3 2 d q d q 4 8 , 4 , 2 , 1 8 , 9 , 1 0 , 1 1 r o w i n t e r c o n n e c t d e d i c a t e d c l o c k s 2 4 , 8 c h i p - w i d e r e s e t
14 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation when used as ram, each eab can be configured in any of the following sizes: 256 16, 512 8, 1,024 4, or 2,048 2 (see figure 5 ). figure 5. flex 10ke eab memor y con gurations larger blocks of ram are created by combining multiple eabs. for example, two 256 16 ram blocks can be combined to form a 256 32 block; two 512 8 ram blocks can be combined to form a 512 16 block (see figure 6 ). figure 6. examples of combining flex 10ke eabs if necessary, all eabs in a device can be cascaded to form a single ram block. eabs can be cascaded to form ram blocks of up to 2,048 words without impacting timing. the quartus and max+plus ii software automatically combines eabs to meet a designer? ram specifications. 2 5 6 1 6 5 1 2 8 1 , 0 2 4 4 2 , 0 4 8 2 5 1 2 8 5 1 2 8 2 5 6 1 6 2 5 6 1 6 2 5 6 3 2 5 1 2 1 6
altera corporation 15 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet eabs provide flexible options for driving and controlling clock signals. different clocks and clock enables can be used for reading and writing to the eab. registers can be independently inserted on the data input, eab output, write address, write enable s ignals, read address, and read enable s ignals. the global signals and the eab local interconnect can drive write enable, read enable, and clock enable signals. the global signals, dedicated clock pins, and eab local interconnect can drive the eab clock signals. because the les drive the eab local interconnect, the les can control write enable, read enable, clear, clock, and clock enable signals. an eab is fed by a row interconnect and can drive out to row and column interconnects. each eab output can drive up to two row channels and up to two column channels; the unused row channel can be driven by other les. this feature increases the routing resources available for eab outputs (see figures 2 and 4 ). the column interconnect, which is adjacent to the eab, has twice as many channels as other columns in the device. logic a rray block an lab consists of eight les, their associated carry and cascade chains, lab control signals, and the lab local interconnect. the lab provides the coarse-grained structure to the flex 10ke architecture, facilitating efficient routing with optimum device utilization and high performance (see figure 7 ).
16 altera corporation flex 10ke embe d ded p r ogrammable logic f ami l y data sheet preliminary in f ormation figure 7. flex 10ke lab notes: (1) epf10k30e, epf10k50e, and epf10k50s devices have 2 2 inputs to the lab local interconnect channel from the row; epf10k100e, epf10k100b, EPF10K130E, epf10k200e, and epf10k200 s devices have 26. (2) epf10k30e, epf10k50e, and epf10k50s devices have 30 lab local interconnect channels; epf10k100e, epf10k100b, EPF10K130E, epf10k200e, and epf10k200 s devices have 34. (3) in epf10k100b devices, four row channels can drive column channels at each intersection. 2 8 c a r r y - i n & c a s c a d e - i n l e 1 l e 8 l e 2 l e 3 l e 4 l e 5 l e 6 l e 7 c o l u m n i n t e rconnect r o w i n t e rconnect ( 1 ) l a b l o c a l interconnect ( 2 ) c o l u m n - t o - r o w i n t e rconnect c a r r y - o u t & c a s c a d e - o u t 1 6 2 4 t o 4 8 l a b c o n t r o l s i g n a l s s e e f i g u r e 1 2 f o r d e t a i l s . 6 d e d i c a t e d i n p u t s & g l o b a l s i g n a l s 16 6 8 4 4 4 4 4 4 4 4 4 4 2 8 ( 3 )
altera corporation 17 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet each lab provides four control signals with programmable inversion that can be used in all eight les. two of these signals can be used as clocks , t he other two can be used for clea r/preset control. the lab clocks can be driven by the dedicated clock input pins, global signals, i/o signals, or internal signals via the lab local interconnect. the lab preset and clear control signals can be driven by the global signals, i/o signals, or internal signals via the lab local interconnect. the global control signals are typically used for global clock, clear, or preset signals because they provide asynchronous control with very low skew across the device. if logic is required on a control signal, it can be generated in one or more le i n any lab and driven into the local interconnect of the target lab. in addition, the global control signals can be generated from le outputs. logic ele ment the le, the smallest unit of logic in the flex 10ke architecture, has a compact size that provides efficient logic utilization. each le contains a 4- input lut, which is a function generator that can quickly compute any function of four variables. in addition, each le contains a programmable flipflop with a synchronous clock enable, a carry chain, and a cascade chain. each le drives both the local and the fasttrack interconnect routing structure (see figure 8 ). figure 8. flex 10ke logic element t o l a b l o c a l i n t e r c o n n e c t c a r r y - i n c l o c k s e l e c t c a r r y - o u t l o o k - u p t a b l e ( l u t ) c l e a r / p r e s e t l o g i c c a r r y c h a i n c a s c a d e c h a i n c a s c a d e - i n c a s c a d e - o u t t o f a s t t r a c k i n t e r c o n n e c t p r o g r a m m a b l e r e g i s t e r p r n c l r n d q e n a r e g i s t e r b y p a s s d a t a 1 d a t a 2 d a t a 3 d a t a 4 l a b c t r l 1 l a b c t r l 2 l a b c t r l 4 l a b c t r l 3 c h i p - w i d e r e s e t
18 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation the programmable flipflop in the le can be configured for d, t, jk, or sr operation. the clock, clear, and preset control signals on the flipflop can be driven by global signals, general-purpose i/o pins, or any internal logic. for combinatorial functions, the flipflop is bypassed and the output of the lut drives the output of the le. the le has two outputs that drive the interconnect : o ne drives the local interconnect and the other drives either the row or column fasttrack interconnect routing structure. the two outputs can be controlled independently . fo r example, the lut can drive one output while the register drives the other output. this feature, called register packing, can improve le utilization because the register and the lut can be used for unrelated functions. the flex 10ke architecture provides two types of dedicated high-speed data paths that connect adjacent les without using local interconnect paths: carry chains and cascade chains. the carry chain supports h igh-speed counters and adders and t he cascade chain implements w ide-input functions with minimum delay. carry and cascade chains connect all les in a lab as well as a ll labs in the same row. intensive use of carry and cascade chains can reduce routing flexibility. therefore, the use of these chains should be limited to speed-critical portions of a design. carr y chain the carry chain provides a very fast (as low as 0.2 ns) carry-forward function between les. the carry-in signal from a lower-order bit drives forward into the higher-order bit via the carry chain, and feeds into both the lut and the next portion of the carry chain. this feature allows the flex 10ke architecture to implement high-speed counters, adders, and comparators of arbitrary width efficiently. carry chain logic can be created automatically by the quartus and max+plus ii compilers during design processing, or manually by the designer during design entry. parameterized functions such as lpm and designware functions automatically take advantage of carry chains. carry chains longer than eight les are automatically implemented by linking labs together. for enhanced fitting, a long carry chain skips alternate labs in a row. a carry chain longer than one lab skips either from even-numbered lab to even-numbered lab, or from odd- numbered lab to odd-numbered lab. for example, the last le of the first lab in a row carries to the first le of the third lab in the row. the carry chain does not cross the eab at the middle of the row. for instance, in the epf10k50e device, the carry chain stops at the eighteenth lab and a new one begins at the nineteenth lab.
altera corporation 19 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet figure 9 shows how an n -bit full adder can be implemented in n + 1 les with the carry chain. one portion of the lut generates the sum of two bits using the input signals and the carry-in signal; the sum is routed to the output of the le. the register can be bypassed for simple adders or used for an accumulator function. another portion of the lut and the carry chain logic generates the carry-out signal, which is routed directly to the carry-in signal of the next-higher-order bit. the final carry-out signal is routed to an le, where it can be used as a general-purpose signal. figure 9. flex 10ke carr y chain operation ( n- bit full adder) l u t a 1 b 1 c a r r y c h a i n s 1 l e 1 r e g i s t e r a 2 b 2 c a r r y c h a i n s 2 l e 2 r e g i s t e r c a r r y c h a i n s n l e n r e g i s t e r a n b n c a r r y c h a i n c a r r y - o u t l e n + 1 r e g i s t e r c a r r y - i n l u t l u t l u t
20 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation casca de chain with the cascade chain, the flex 10ke architecture can implement functions that have a very wide fan-in. adjacent luts can be used to compute portions of the function in parallel; the cascade chain serially connects the intermediate values. the cascade chain can use a logical and or logical or (via de morgan? inversion) to connect the outputs of adjacent les. with a delay as low as 0.6 ns per le, each additional le provides four more inputs to the effective width of a function. cascade chain logic can be created automatically by the max+plus ii compiler during design processing, or manually by the designer during design entry. cascade chains longer than eight bits are implemented automatically by linking several labs together. for easier routing, a long cascade chain skips every other lab in a row. a cascade chain longer than one lab skips either from even-numbered lab to even-numbered lab, or from odd-numbered lab to odd-numbered lab (e.g., the last le of the first lab in a row cascades to the first le of the third lab). the cascade chain does not cross the center of the row (e.g., in the epf10k50e device, the cascade chain stops at the eighteenth lab and a new one begins at the nineteenth lab). this break is due to the eab? placement in the middle of the row. figure 10 shows how the cascade function can connect adjacent les to form functions with a wide fan-in. these examples show functions of 4 n variables implemented with n les. the le delay is 1.3 ns; the cascade chain delay is 0.6 ns. with the cascade chain, 3 .1 ns are needed to decode a 16-bit address.
altera corporation 21 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet figure 10. flex 10ke cascade chain operation le operatin g modes the flex 10ke le can operate in the following four modes: n normal mode n arithmetic mode n up/down counter mode n clearable counter mode each of these modes uses le resources differently. in each mode, seven available inputs to the le?he four data inputs from the lab local interconnect, the feedback from the programmable register, and the carry-in and cascade-in from the previous le?re directed to different destinations to implement the desired logic function. three inputs to the le provide clock, clear, and preset control for the register. the quartus and max+plus ii software, in conjunction with parameterized functions such as lpm and designware functions, automatically chooses the appropriate mode for common functions such as counters, adders, and multipliers. if required, the designer can also create special-purpose functions that use a specific le operating mode for optimal performance. the architecture provides a synchronous clock enable to the register in all four modes. the quartus and max+plus ii software can set data1 to enable the register synchronously, providing easy implementation of fully synchronous designs. l e 1 l u t l e 2 l u t d [ 3 . . 0 ] d [ 7 . . 4 ] d [ ( 4 n 1 ) . . ( 4 n 4 ) ] d [ 3 . . 0 ] d [ 7 . . 4 ] l e n l e 1 l e 2 l e n l u t l u t l u t l u t a n d c a s c a d e c h a i n o r c a s c a d e c h a i n d [ ( 4 n 1 ) . . ( 4 n 4 ) ]
22 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation figure 11 shows the le operating modes. figure 11. flex 10ke le operating modes e n a p r n c l r n d q 4 - i n p u t l u t c a r r y - i n c a s c a d e - o u t c a s c a d e - i n l e - o u t t o f a s t t r a c k i n t e r c o n n e c t l e - o u t t o l o c a l i n t e r c o n n e c t e n a n o r m a l m o d e p r n c l r n d q c a s c a d e - o u t l e - o u t c a s c a d e - i n 3 - i n p u t l u t c a r r y - i n 3 - i n p u t l u t c a r r y - o u t a r i t h m e t i c m o d e u p / d o w n c o u n t e r m o d e p r n c l r n d q 3 - i n p u t l u t c a r r y - i n c a s c a d e - i n l e - o u t 3 - i n p u t l u t c a r r y - o u t 1 0 c a s c a d e - o u t c l e a r a b l e c o u n t e r m o d e p r n c l r n d q 3 - i n p u t l u t c a r r y - i n l e - o u t 3 - i n p u t l u t c a r r y - o u t 1 0 c a s c a d e - o u t e n a e n a d a t a 1 d a t a 4 d a t a 3 d a t a 2 d a t a 1 d a t a 2 d a t a 1 ( e n a ) d a t a 2 ( u / d ) d a t a 4 ( n l o a d ) d a t a 3 ( d a t a ) d a t a 1 ( e n a ) d a t a 2 ( n c l r ) d a t a 4 ( n l o a d ) d a t a 3 ( d a t a )
altera corporation 23 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet normal mode the normal mode is suitable for general logic applications and wide decoding functions that can take advantage of a cascade chain. in normal mode, four data inputs from the lab local interconnect and the carry-in are inputs to a 4-input lut. the max+plus ii compiler automatically selects the carry-in or the data3 signal as one of the inputs to the lut. the lut output can be combined with the cascade-in signal to form a cascade chain through the cascade-out signal. either the register or the lut can be used to drive both the local interconnect and the fasttrack interconnect routing structure at the same time. the lut and the register in the le can be used independently (register packing). t o support register packing, the le has two outputs; one drives the local interconnect, and the other drives the fasttrack interconnect routing structure. the data4 signal can drive the register directly, allowing the lut to compute a function that is independent of the registered signal; a 3-input function can be computed in the lut, and a fourth independent signal can be registered. alternatively, a 4-input function can be generated, and one of the inputs to this function can be used to drive the register. the register in a packed le can still use the clock enable, clear, and preset signals in the le. in a packed le, the register can drive the fasttrack interconnect routing structure while the lut drives the local interconnect, or vice versa. arithmetic mode the arithmetic mode offers two 3-input luts that are ideal for implementing adders, accumulators, and comparators. one lut computes a 3-input function; the other generates a carry output. as shown in figure 11 on page 22 , the first lut uses the carry-in signal and two data inputs from the lab local interconnect to generate a combinatorial or registered output. for example, in an adder, this output is the sum of three signals: a , b , and carry-in. the second lut uses the same three signals to generate a carry-out signal, thereby creating a carry chain. the arithmetic mode also supports simultaneous use of the cascade chain. up/down counter mode the up/down counter mode offers counter enable, clock enable, synchronous up/down control, and data loading options. these control signals are generated by the data inputs from the lab local interconnect, the carry-in signal, and output feedback from the programmable register. two 3-input luts are used: one generates the counter data, and the other generates the fast carry bit. a 2-to-1 multiplexer provides synchronous loading. data can also be loaded asynchronously with the clear and preset register control signals, without using the lut resources.
24 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation clearable counter mode the clearable counter mode is similar to the up/down counter mode, but supports a synchronous clear instead of the up/down control. the clear function is substituted for the cascade-in signal in the up/down counter mode. two 3-input luts are used: one generates the counter data, and the other generates the fast carry bit. synchronous loading is provided by a 2- to-1 multiplexer. the output of this multiplexer is and ed with a synchronous clear signal. internal t ri-state emulation internal tri-state emulation provides internal tri-states without the limitations of a physical tri-state bus. in a physical tri-state bus, the tri-state buffers?output enable ( oe ) signals select which signal drives the bus. however, if multiple oe signals are active, contending signals can be driven onto the bus. conversely, if no oe signals are active, the bus will float. internal tri-state emulation resolves contending tri-state buffers to a low value and floating buses to a high value, thereby eliminating these problems. the max+plus ii software automatically implements tri-state bus functionality with a multiplexer. clear & preset logic control logic for the programmable register? clear and preset functions is controlled by the data3 , labctrl1 , and labctrl2 inputs to the le. the clear and preset control structure of the le asynchronously loads signals into a register. either labctrl1 or labctrl2 can control the asynchronous clear. alternatively, the register can be set up so that labctrl1 implements an asynchronous load. the data to be loaded is driven to data3 ; when labctrl1 is asserted, data3 is loaded into the register. during compilation, the quartus and max+plus ii compilers automatically select the best control signal implementation. because the clear and preset functions are active-low, the compiler automatically assigns a logic high to an unused clear or preset. the clear and preset logic is implemented in one of the following six modes chosen during design entry: n asynchronous clear n asynchronous preset n asynchronous clear and preset n asynchronous load with clear n asynchronous load with preset n asynchronous load without clear or preset
altera corporation 25 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet in addition to the six clear and preset modes, flex 10ke devices provide a chip-wide reset pin that can reset all registers in the device. use of this feature is set during design entry. in any of the clear and preset modes, the chip-wide reset overrides all other signals. registers with asynchronous presets may be preset when the chip-wide reset is asserted. inversion can be used to implement the asynchronous preset. figure 12 shows examples of how to setup the preset and clear inputs for the desired functionality. figure 12. flex 10ke le clear & preset modes a s y n c h r o n o u s c l e a r a s y n c h r o n o u s p r e s e t a s y n c h r o n o u s p r e s e t & c l e a r a s y n c h r o n o u s l o a d w i t h o u t c l e a r o r p r e s e t l a b c t r l 1 ( a s y n c h r o n o u s l o a d ) p r n c l r n d q n o t n o t l a b c t r l 1 ( a s y n c h r o n o u s l o a d ) a s y n c h r o n o u s l o a d w i t h c l e a r l a b c t r l 2 ( c l e a r ) p r n c l r n d q n o t n o t ( a s y n c h r o n o u s l o a d ) a s y n c h r o n o u s l o a d w i t h p r e s e t n o t n o t p r n c l r n d q l a b c t r l 1 o r l a b c t r l 2 p r n c l r n d q v c c c h i p - w i d e r e s e t c h i p - w i d e r e s e t c h i p - w i d e r e s e t c h i p - w i d e r e s e t p r n c l r n d q p r n c l r n d q v c c c h i p - w i d e r e s e t c h i p - w i d e r e s e t d a t a 3 ( d a t a ) l a b c t r l 1 l a b c t r l 2 ( p r e s e t ) d a t a 3 ( d a t a ) d a t a 3 ( d a t a ) l a b c t r l 1 o r l a b c t r l 2 l a b c t r l 1 l a b c t r l 2
26 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation asynchronous clear the flipflop can be cleared by either labctrl1 or labctrl2 . in this mode, the preset signal is tied to vcc to deactivate it. asynchronous preset an asynchronous preset is implemented as an asynchronous load, or with an asynchronous clear. if data3 is tied to vcc , asserting labctrl1 asynchronously loads a one into the register. alternatively, the max+plus ii software can provide preset control by using the clear and inverting the input and output of the register. inversion control is available for the inputs to both les and ioes. therefore, if a register is preset by only one of the two labctrl signals, the data3 input is not needed and can be used for one of the le operating modes. asynchronous preset & clear when implementing asynchronous clear and preset, labctrl1 controls the preset and labctrl2 controls the clear. data3 is tied to vcc , so that asserting labctrl1 asynchronously loads a one into the register, effectively presetting the register. asserting labctrl2 clears the register. asynchronous load with clear when implementing an asynchronous load in conjunction with the clear, labctrl1 implements the asynchronous load of data3 by controlling the register preset and clear. labctrl2 implements the clear by controlling the register clear; labctrl2 does not have to feed the preset circuits. asynchronous load with preset when implementing an asynchronous load in conjunction with preset, the max+plus ii software provides preset control by using the clear and inverting the input and output of the register. asserting labctrl2 presets the register, while asserting labctrl1 loads the register. the max+plus ii software inverts the signal that drives data3 to account for the inversion of the register? output. asynchronous load without preset or clear when implementing an asynchronous load without preset or clear, labctrl1 implements the asynchronous load of data3 by controlling the register preset and clear.
altera corporation 27 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet fastt rack interc onnect routing structure in the flex 10ke architecture, connections between les, eabs, and device i/o pins are provided by the fasttrack interconnect routing structure, which is a series of continuous horizontal and vertical routing channels that traverses the device. this global routing structure provides predictable performance, even in complex designs. in contrast, the segmented routing in fpgas requires switch matrices to connect a variable number of routing paths, increasing the delays between logic resources and reducing performance. the fasttrack interconnect routing structure consists of row and column interconnect channels that span the entire device. each row of labs is served by a dedicated row interconnect. the row interconnect can drive i/o pins and feed other labs in the row. the column interconnect routes signals between rows and can drive i/o pins. row channels drive into the lab or eab local interconnect. the row signal is buffered at every lab or eab to reduce the effect of fan-out on delay. a row channel can be driven by an le or by one of three column channels. these four signals feed dual 4-to-1 multiplexers that connect to two specific row channels. these multiplexers, which are connected to each le, allow column channels to drive row channels even when all eight les in a lab drive the row interconnect. each column of labs or eabs is served by a dedicated column interconnect. the column interconnect that serves the eabs has twice as many channels as other column interconnects. the column interconnect can then drive i/o pins or another row? interconnect to route the signals to other labs or eabs in the device. a signal from the column interconnect, which can be either the output of a le or an input from an i/o pin, must be routed to the row interconnect before it can enter a lab or eab. each row channel that is driven by an ioe or eab can drive one specific column channel. access to row and column channels can be switched between les in adjacent pairs of labs. for example, a le in one lab can drive the row and column channels normally driven by a particular le in the adjacent lab in the same row, and vice versa. this f lexibility enables routing resources to be used more efficiently (see figure 13 ).
28 altera corporation flex 10ke embe d ded p r ogrammable logic f ami l y data sheet preliminary in f ormation figure 13. flex 10ke lab connections to row & column interconnect note: (1) in epf10k100b devices, four row channels can drive column channels at each intersection. f r o m a d j a c e n t l a b r o w c h a n n e l s c o l u m n c h a n n e l s each le can drive two r o w c h a n n e l s . l e 2 l e 8 l e 1 t o a d j a c e n t l a b e a c h l e c a n s w i t c h i n t e rconnect access w i t h a n l e i n t h e a d j a c e n t l a b . a t e a c h i n t e r s e c t i o n , s i x r o w c h a n n e l s c a n d r i v e c o l u m n c h a n n e l s ( 1 ) . t o o t h e r r o w s t o l a b l o c a l i n t e r c o n n e c t t o o t h e r c o l u m n s
altera corporation 29 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet for improved routing, the row interconnect consists of a combination of full-length and half-length channels. the full-length channels connect to all labs in a row; the half-length channels connect to the labs in half of the row. the eab can be driven by the half- length channels in the left half of the row and by the full-length channels. the eab drives out to the full- length channels. in addition to providing a predictable, row-wide interconnect, this architecture provides increased routing resources. two neighboring labs can be connected using a half-row channel, thereby saving the other half of the channel for the other half of the row. table 7 summarizes the fasttrack interconnect routing structure resources available in each flex 10ke device. in addition to general-purpose i/o pins, flex 10ke devices have six dedicated input pins that provide low-skew signal distribution across the device. these six inputs can be used for global clock, clear, preset, and peripheral output enable and clock enable control signals. these signals are available as control signals for all labs and ioes in the device. the dedicated inputs can also be used as general-purpose data inputs because they can feed the local interconnect of each lab in the device. figure 14 shows the interconnection of adjacent labs and eabs, with row, column, and local interconnects, as well as the associated cascade and carry chains. each lab is labeled according to its location: a letter represents the row and a number represents the column. for example, lab b3 is in row b, column 3. table 7. flex 10ke fasttrack interconnect resources device rows channels per row columns channels per column epf10k30e 6 216 36 24 epf10k50e epf10k50s 10 216 36 24 epf10k100b epf10k100e 12 312 52 24 EPF10K130E 16 312 52 32 epf10k200e epf10k200s 24 312 52 48
30 altera corporation flex 10ke embe d ded p r ogrammable logic f ami l y data sheet preliminary in f ormation figure 14. flex 10ke interconnect resources i/o ele ment an ioe contains a bidirectional i/o buffer and a register that can be used either as an input register for external data that requires a fast setup time, or as an output register for data that requires fast clock-to-output performance. in some cases, using an le register for an input register will result in a faster setup time than using an ioe register. ioes can be used as input, output, or bidirectional pins. the quartus and max+plus ii compilers use the programmable inversion option to invert signals from the row and column interconnect automatically where appropriate. figure 15 shows the ioe block diagram. i / o e l e m e n t ( i o e ) r o w interconnect i o e i o e i o e i o e c o l u m n i n t e r c o n n e c t l a b b 1 s e e f i g u r e 1 7 f o r d e t a i l s . s e e f i g u r e 1 6 f o r d e t a i l s . l a b a3 l a b b 3 l a b a 1 l a b a 2 l a b b 2 i o e i o e c a s c a d e & to lab b4 to lab a4 to lab b5 to lab a5 i o e i o e i o e i o e i o e i o e i o e i o e i o e i o e i o e i o e i o e i o e c a r r y c h a i n s
altera corporation 31 preliminary in f ormation flex 10ke embe d ded p r ogrammable logic f ami l y data sheet figure 15. flex 10ke bidirectional i/o registers note: (1) selected flex 10ke devices include programmable delay buffers on the input path. v c c o e [ 7 . . 0 ] c l k [ 1 . . 0 ] e n a [ 5 . . 0 ] c l r n [ 1 . . 0 ] p e r i p h e r a l c o n t r o l b u s c l r n d q e n a v c c 2 d e d i c a t e d c l o c k i n p u t s s l e w - r a t e c o n t r o l o p e n - d r a i n o u t p u t c h i p - w i d e o u t p u t e n a b l e c l k [ 3 . . 2 ] 2 1 2 v c c v c c c h i p - w i d e r e s e t p r o gramma b l e d e l a y ( 1 ) 4 d e d i c a t e d i n p u t s r o w a n d c o l u m n i n t e r c o n n e c t 4 v c c c l r n d q e n a c h i p - w i d e r e s e t c l r n d q e n a c h i p - w i d e r e s e t v c c i n p u t r e g i s t e r o u t p u t r e g i s t e r o e r e g i s t e r
32 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation on all flex 10ke devices (except epf10k50e and epf10k200e), the input path from the i/o pad to the fasttrack interconnect has a programmable delay element that can be used to guarantee a zero hold time. epf10k50s and epf10k200s devices support this feature. depending on the placement of the ioe relative to what it is driving, the designer may choose to turn on the programmable delay to ensure a zero hold time or turn it off to minimize setup time. this feature is used to reduce setup time for complex pin-to-register paths (e.g., pci designs). each ioe selects the clock, clear, clock enable, and output enable controls from a network of i/o control signals called the peripheral control bus. the peripheral control bus uses high-speed drivers to minimize signal skew across devices and provides up to 12 peripheral control signals that can be allocated as follows: n up to eight output enable signals n up to six clock enable signals n up to two clock signals n up to two clear signals if more than six clock enable or eight output enable signals are required, each ioe on the device can be controlled by clock enable and output enable signals driven by specific les. in addition to the two clock signals available on the peripheral control bus, each ioe can use one of two dedicated clock pins. each peripheral control signal can be driven by any of the dedicated input pins or the first le of each lab in a particular row. in addition, a le in a different row can drive a column interconnect, which causes a row interconnect to drive the peripheral control signal. the chip- wide reset signal resets all ioe registers, overriding any other control signals. when a dedicated clock pin drives ioe registers, it can be inverted for all ioes in the device. all ioes must use the same sense of the clock. for example, if any ioe uses the inverted clock, all ioes must use the inverted clock and no ioe can use the non-inverted clock. however, les can still use the true or complement of the clock on a lab-by-lab basis. the incoming signal may be inverted at the dedicated clock pin and will drive all ioes. for t he true and complement of a clock to be used to drive ioes, drive it into both global clock pins. one global clock pin will supply the true, and the other will supply the complement. when the true and complement of a dedicated input drives ioe clocks, t wo signals on the peripheral control bus are consumed, one for each sense of the clock.
altera corporation 33 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet when dedicated inputs drive non-inverted and inverted peripheral clears, clock enables, and output enables, two signals on the peripheral control bus will be used. tables 8 and 9 list the sources for each peripheral control signal, and show how the output enable, clock enable, clock, and clear signals share 12 peripheral control signals. the tables also show the rows that can drive global signals. table 8. epf10k30e, epf10k50e & epf10k50s peripheral bus sources peripheral control signal epf10k30e epf10k50e epf10k50s oe0 row a row a oe1 row b row b oe2 row c row d oe3 row d row f oe4 row e row h oe5 row f row j clkena0/clk0/global0 row a row a clkena1/oe6/global1 row b row c clkena2/clr0 row c row e clkena3/oe7/global2 row d row g clkena4/clr1 row e row i clkena5/clk1/global3 row f row j
34 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation signals on the peripheral control bus can also drive the four global signals, referred to as global0 through global3 in tables 8 and 9 . an internally generated signal can drive a global signal, providing the same low- skew, low-delay characteristics as a signal driven by an input pin. an le drives the global signal by driving a row line that drives the peripheral bus, which then drives the global signal. this feature is ideal for internally generated clear or clock signals with high fan-out. however, internally driven global signals offer no advantage over the general-purpose interconnect for routing data signals. the chip-wide output enable pin is an active-low pin that can be used to tri-state all pins on the device. this option can be set in the max+plus ii software. on epf10k50e and epf10k200e devices, the built-in i/o pin pull-up resistors (which are active during configuration) are active when the chip-wide output enable pin is asserted. t he registers in the ioe can also be reset by the chip-wide reset pin. table 9. epf10k100b, epf10k100e, EPF10K130E, epf10k200e & epf10k200s p eripheral bus sources peripheral control signal epf10k100b epf 10k100e epf10 k 130e epf10k 2 00e epf10k200s oe0 row a row c row g oe1 row c row e row i oe2 row e row g row k oe3 row l row n row r oe4 row i row k row o oe5 row k row m row q clkena0/clk0/global0 row f row h row l clkena1/oe6/global1 row d row f row j clkena2/clr0 row b row d row h clkena3/oe7/global2 row h row j row n clkena4/clr1 row j row l row p clkena5/clk1/global3 row g row i row m
altera corporation 35 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet row-to-ioe connections when an ioe is used as an input signal, it can drive two separate row channels. the signal is accessible by all les within that row. when an ioe is used as an output, the signal is driven by a multiplexer that selects a signal from the row channels. up to eight ioes connect to each side of each row channel (see figure 16 ). figure 16. flex 10ke row-to-ioe connections table 10 lists the flex 10ke row-to-ioe interconnect resources. n n e a c h i o e i s d r i v e n b y a n m - t o - 1 m u l t i p l e x e r . e a c h i o e c a n d r i v e t w o r o w c h a n n e l s . i o e 8 i o e 1 m m r o w f a s t t r a c k i n t e r c o n n e c t n the values for m and n are provided in t able 10 . table 10. flex 10ke row-to-ioe interconnect resources device channels per row (n) row channels per pin (m) epf10k30e 216 27 epf10k50e epf10k50s 216 27 epf10k100b epf10k100e 312 39 EPF10K130E 312 39 epf10k200e epf10k200s 312 39
36 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation column-to-ioe connections when an ioe is used as an input, it can drive up to two separate column channels. when an ioe is used as an output, the signal is driven by a multiplexer that selects a signal from the column channels. two ioes connect to each side of the column channels. each ioe can be driven by column channels via a multiplexer. the set of column channels is different for each ioe (see figure 17 ). figure 17. flex 10ke column-to-ioe connections table 11 lists the flex 10ke column-to-ioe interconnect resources. e a c h i o e i s d r i v e n b y a m - t o - 1 m u l t i p l e x e r e a c h i o e c a n d r i v e t w o c o l u m n c h a n n e l s . c o l u m n i n t e r c o n n e c t n n m m n i o e 1 i o e 1 the values for m and n are provided in t able 11 . table 11. flex 10ke column-to-ioe interconnect resources device channels per column (n) column channels per pin (m) epf10k30e 24 16 epf10k50e epf10k50s 24 16 epf10k100b epf10k100e 24 16 EPF10K130E 32 24 epf10k200e epf10k200s 48 40
altera corporation 37 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet s am eframe pin-outs flex 10ke devices support the sameframe pin-out feature for f ineline bga packages. the sameframe pin-out feature is the arrangement of balls on fineline bga packages such that the lower-ball- count packages form a subset of the higher-ball-count packages. sameframe pin-outs provide the flexibility to migrate not only from device to device within the same package, but also from one package to another. a given printed circuit board (pcb) layout can support multiple device density/package combinations. for example, a single board layout can support a range of devices from an epf10k30e device in a 256-pin fineline bga package to an epf10k200s device in a 672-pin fineline bga package. the quartus and max+plus ii software p rovides support to design pcbs with sameframe pin-out devices. devices can be defined for present and future use . the quartus and m ax+plus ii software generates pin-outs describing how to lay out a board to take advantage of this migration (see figure 18 ). figure 18. sameframe pin-out example d e s i g n e d f o r 2 5 6 - p i n f i n e l i n e b g a p a c k a g e p r i n t e d c i r c u i t b o a r d 1 0 0 - p i n f i n e l i n e b g a p a c k a g e ( r e d u c e d i / o c o u n t o r l o g i c r e q u i r e m e n t s ) 2 5 6 - p i n f i n e l i n e b g a p a c k a g e ( i n c r e a s e d i / o c o u n t o r l o g i c r e q u i r e m e n t s ) 1 0 0 - p i n f i n e l i n e b g a 2 5 6 - p i n f i n e l i n e b g a
38 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation cloc klock & clock boo st features to support high-speed designs, flex 10ke devices offer optional clocklock and clockboost circuitry containing a phase-locked loop (pll) that is used to increase design speed and reduce resource usage. the clocklock circuitry uses a synchronizing pll that reduces the clock delay and skew within a device. this reduction minimizes clock-to-output and setup times while maintaining zero hold times. the clockboost circuitry, which provides a clock multiplier, allows the designer to enhance device area efficiency by resource sharing within the device. the clockboost feature allows the designer to distribute a low-speed clock and multiply that clock on-device. combined, the clocklock and clockboost features provide significant improvements in system performance and bandwidth. all flex 10ke devices, except epf10k50e devices, support clocklock and clockboost circuitry. epf10k50s and epf10k200s devices support this circuitry. devices that support clocklock and clockboost circuitry are distinguished with an ??suffix in the ordering code; for instance, the epf10k200efc672-1x device supports this circuit. the clocklock and clockboost features in flex 10ke devices are enabled through the quartus and max+plus ii software. external devices are not required to use these features. the output of the clocklock and clockboost circuits is not available at any of the device pins. the clocklock and clockboost circuitry locks onto the rising edge of the incoming clock. the circuit output can drive the clock inputs of registers only; the generated clock cannot be gated or inverted. the dedicated clock pin ( gclk1 ) supplies the clock to the clocklock and clockboost circuitry. when the dedicated clock pin is driving the clocklock or clockboost circuitry, it cannot drive elsewhere in the device. for designs that require both a multiplied and non-multiplied clock, the clock trace on the board can be connected to the gclk1 pin. in the max+plus ii software, the gclk1 pin can feed both the clocklock and clockboost circuitry in the flex 10ke device. however, when both circuits are used, the other clock pin cannot be used.
altera corporation 39 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet clocklock & clockboost t iming parameters for the clocklock and clockboost circuitry to function properly, the incoming clock must meet certain requirements. if these specifications are not met, the circuitry may not lock onto the incoming clock, which generates an erroneous clock within the device. the clock generated by the clocklock and clockboost circuitry must also meet certain specifications. if the incoming clock meets these requirements during configuration, the clocklock and clockboost circuitry will lock onto the clock during configuration. the circuit will be ready for use immediately after configuration. figure 19 shows the incoming and generated clock specifications. figure 19. speci cations for the incoming & generated clocks the t i parameter refers to the nominal input clock period; the t o parameter refers to the nominal output clock period. t r t f t clk1 t induty t i f clkdev t i t i t inclkstb t outduty t o t o + t jitter t o C t jitter input cloc k cloc kloc k- gener ated cloc k
40 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation tables 12 and 13 summarize the clocklock and clockboost parameters for -1 and -2 speed-grade devices, respectively. table 12. clocklock & clock boost parameters for -1 speed-grade devices symbol parameter condition min typ max unit t r input rise time 5 ns t f input fall time 5 ns t induty input duty cycle 40 60 % f clk1 input clock frequency (clockboost clock multiplication factor equals 1) 25 180 mhz f clk2 input clock frequency (clockboost clock multiplication factor equals 2) 16 90 mhz f clkdev input deviation from user specification in the quartus software (clockboost clock multiplication factor equals 1) (1) 25,000 (2) ppm t inclkstb input clock stability (measured between adjacent clocks) 100 ps t lock time required for clocklock or clockboost to acquire lock (3) 10 ? t jitter jitter on clocklock or clockboost- generated clock (4) t inclkstb < 100 250 ps t inclkstb < 50 200 (4) ps t outduty duty cycle for clocklock or clockboost-generated clock 40 50 60 %
altera corporation 41 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet notes: (1) to implement the clocklock and clockboost circuitry with the max+plus ii software, designers must specify the input frequency. the max+plus ii software tunes the pll in the clocklock and clockboost circuitry to this frequency. the f clkdev parameter specifies how much the incoming clock can differ from the specified frequency during device operation. simulation does not reflect this parameter. (2) twenty-five thousand parts per million (ppm) equates to 2.5 % of input clock period. (3) during device configuration, the clocklock and clockboost circuitry is configured before the rest of the device. if the incoming clock is supplied during configuration, the clocklock and clockboost circuitry locks during configuration because the t lock value is less than the time required for configuration. (4) the t jitter specification is m easured under long-term observation. the maximum value for t jitter is 200 ps if t inclkstb is lower than 50 p s. i/o con guration this section discusses the peripheral component interconnect (pci) pull-up clamping diode option, slew-rate control, open-drain output option, and multivolt i/o interface for flex 10ke devices. the pci pull-up clamping diode, slew-rate control, and open-drain output options are controlled pin-by-pin via max+plus ii logic options. the multivolt i/o interface is controlled by connecting v ccio to a different voltage than v ccint . its effect can be simulated in the max+plus ii software via the g lobal project device options dialog box ( assign menu). table 13. clocklock & clock boost parameters for -2 speed-grade devices symbol parameter condition min typ max unit t r input rise time 5 ns t f input fall time 5 ns t induty input duty cycle 40 60 % f clk1 input clock frequency (clockboost clock multiplication factor equals 1) 25 75 mhz f clk2 input clock frequency (clockboost clock multiplication factor equals 2) 16 37.5 mhz f clkdev input deviation from user specification in the quartus software (clockboost clock multiplication factor equals 1) (1) 25,000 (2) ppm t inclkstb input clock stability (measured between adjacent clocks) 100 ps t lock time required for clocklock or clockboost to acquire lock (3) 10 ? t jitter jitter on clocklock or clockboost- generated clock (4) t inclkstb < 100 250 ps t inclkstb < 50 200 (4) ps t outduty duty cycle for clocklock or clockboost-generated clock 40 50 60 %
42 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation pci pull- up clamping diode option flex 10ke devices have a pull-up clamping diode on every i/o, dedicated input, and dedicated clock pin. pci clamping diodes clamp the signal to the v ccio value and are required for 3.3-v pci compliance. clamping diodes can also be used to limit overshoot in other systems. clamping diodes are controlled on a pin-by-pin basis . when v ccio is 3 .3 v, a pin that has the clamping diode option turned on can be driven by a 2.5-v or 3.3-v signal, but not a 5.0-v signal. when v ccio is 2.5 v, a pin that has the clamping diode option turned on can be driven by a 2.5-v signal, but not a 3.3-v or 5.0-v signal. additionally, a clamping diode can be activated for a subset of pins, which would allow a device to bridge between a 3.3-v pci bus and a 5.0-v device. slew-r ate control the output buffer in each ioe has an adjustable output slew rate that can be configured for low-noise or high-speed performance. a slower slew rate reduces system noise and adds a maximum delay of 4.3 ns. the fast slew rate should be used for speed-critical outputs in systems that are adequately protected against noise. designers can specify the slew rate pin-by-pin or assign a default slew rate to all pins on a device-wide basis. the slow slew rate setting affects the falling and rising edges of the output. op en-dr ain output option flex 10ke devices provide an optional open-drain output (electrically equivalent to open-collector output) f or each i/o pin. this open-drain output enables the device to provide system-level control signals (e.g., interrupt and write enable signals) that can be asserted by any of several devices. it can also provide an additional wired- or plane. mu ltiv olt i/o interface the flex 10ke device architecture supports the multivolt i/o interface feature, which allows flex 10ke devices in all packages to interface with systems of differing supply voltages. these devices have one set of v cc pins for internal operation and input buffers ( vccint ), and another set for i/o output drivers ( vccio ).
altera corporation 43 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet the vccint pins must always be connected to a 2.5-v power supply. with a 2.5-v v ccint level, input voltages are compatible with 2.5-v, 3.3-v, and 5.0-v inputs. the vccio pins can be connected to either a 2.5-v or 3.3-v power supply, depending on the output requirements. when the v ccio pins are connected to a 2.5-v power supply, the output levels are compatible with 2.5-v systems. when the vccio pins are connected to a 3.3-v power supply, the output high is at 3.3 v and is therefore compatible with 3.3-v or 5.0-v systems. devices operating with v ccio levels higher than 3.0 v achieve a faster timing delay of t od2 instead of t od1 . table 14 summarizes flex 10ke multivolt i/o support. notes: (1) the pci clamping diode must be disabled to drive an input with voltages h igher than v ccio . (2) when v ccio = 3.3 v, a flex 10ke device can drive a 2.5-v device that has 3.3-v tolerant inputs. open-drain output pins on flex 10ke devices (with a pull-up resistor to the 5.0-v supply) can drive 5.0-v cmos input pins that require a v ih of 3.5 v. when the open-drain pin is active, it will drive low. when the pin is inactive, the trace will be pulled up to 5.0 v by the resistor. the open- drain pin will only drive low or tri-state; it will never drive high. the rise time is dependent on the value of the pull-up resistor and load impedance. the i ol current specification should be considered when selecting a pull-up resistor. power sequencing & h ot-socketing because flex 10ke devices can be used in a mixed- voltage environment, they have been designed specifically to tolerate any possible power-up sequence. the v ccio and v ccint power planes can be powered in any order. signals can be driven into flex 10ke devices before and during power up without damaging the device. additionally, flex 10ke devices do not drive out during power up. once operating conditions are reached, flex 10ke devices operate as specified by the user. table 14. flex 10ke multivolt i/o support v ccio (v) input signal (v) output signal (v) 2.5 3.3 5.0 2.5 3.3 5.0 2.5 v v (1) v (1) v 3.3 v v v (1) v (2) v v
44 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation iee e std. 1149.1 (jt ag) boundar y-scan support all flex 10ke devices provide jtag bst circuitry that complies with the ieee std. 1149.1-1990 specification. flex 10ke devices can also be configured using the jtag pins through the bitblaster or byteblastermv d ownload cable , or via hardware that uses the jam tm programming and test language. jtag boundary-scan testing can be performed before or after configuration, but not during configuration. flex 10ke devices support the jtag instructions shown in table 15 . the instruction register length of flex 10ke devices is 10 bits. the usercode register length in flex 10ke devices is 32 bits; 7 bits are determined by the user, and 25 bits are pre-determined. tables 16 and 17 show the boundary-scan register length and device idcode information for flex 10ke devices. table 15. flex 10ke jtag instructions jtag instruction description sample/prelo ad allows a snapshot of signals at the device pins to be captured and examined during normal device operation, and permits an initial data pattern to be output at the device pins. extest allows the external circuitry and board-level interconnections to be tested by forcing a test pattern at the output pins and capturing test results at the input pins. byp ass places the 1-bit bypass register between the tdi and tdo pins, which allows the bst data to pass synchronously through a selected device to adjacent devices during normal device operation. usercode selects the user electronic signature (usercode) register and places it between the tdi and tdo pins, allowing the usercode to be serially shifted out of tdo . idcode selects the idcode register and places it between tdi and tdo , allowing the idcode to be serially shifted out of tdo . icr instr uctions these instructions are used when configuring a flex 10ke device via jtag ports with a bitblaster or byteblastermv download cable, or using a jam file ( .jam ) or jam byte-code file ( .jbc ) via an embedded processor. table 16. flex 10ke boundary-scan register length device boundary-scan register length epf10k30e 690 epf10k50e epf10k50s 798 epf10k100b 873 epf10k100e 1,050 EPF10K130E 1,308 epf10k200e epf10k200s 1,446
altera corporation 45 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet note s : (1) the most significant bit (msb) is on the left. (2) the least significant bit (lsb) for all jtag idcodes is 1 . flex 10ke devices include weak pull-up resistors on the jtag pins. f for more information, see t he following documents: n application note 39 (ieee std. 1149.1 (jtag) boundary-scan testing in altera devices) n bitblaster serial download cable data sheet n byteblastermv parallel port download cable data sheet n jam programming & test language specification table 17. 32-bit idcode for flex 10ke device s note (1) device idcode (32 bits) version (4 bits) part number (16 bits) manufacturer? identity (11 bits) 1 (1 bit) (2) epf10k30e 0001 0001 0000 0011 0000 00001101110 1 epf10k50e epf10k50s 0001 0001 0000 0101 0000 00001101110 1 epf10k100b 0001 0000 0001 0000 0000 00001101110 1 epf10k100e 0010 0000 0001 0000 0000 00001101110 1 EPF10K130E 0001 0000 0001 0011 0000 00001101110 1 epf10k200e epf10k200s 0001 0000 0010 0000 0000 00001101110 1
46 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation figure 20 shows the timing requirements for the jtag signals. figure 20. flex 10ke jt ag w a veforms table 18 shows the timing parameters and values for flex 10ke devices. table 18. flex 10ke jtag timing parameters & values symbol parameter min max unit t jcp tck clock period 100 ns t jch tck clock high time 50 ns t jcl tck clock low time 50 ns t jpsu jtag port setup time 20 ns t jph jtag port hold time 45 ns t jpco jtag port clock to output 25 ns t jpzx jtag port high impedance to valid output 25 ns t jpxz jtag port valid output to high impedance 25 ns t jssu capture register setup time 20 ns t jsh capture register hold time 45 ns t jsco update register clock to output 35 ns t jszx update register high impedance to valid output 35 ns t jsxz update register valid output to high impedance 35 ns t d o t c k t j p z x t j p c o t j p h t j p x z t j c p t j p s u t j c l t j c h t d i t m s s i g n a l t o b e c a p t u r e d s i g n a l t o b e d r i v e n t j s z x t j s s u t j s h t j s c o t j s x z
altera corporation 47 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet gene ri c t esting each flex 10ke device is functionally tested. complete testing of each configurable static random access memory (sram) bit and all logic functionality ensures 100 % yield. ac test measurements for flex 10ke devices are made under conditions equivalent to those shown in figure 21 . multiple test patterns can be used to configure devices during all stages of the production flow. figure 21. flex 10ke ac t est conditions opera ting conditions tables 19 through 23 provide information on absolute maximum ratings, recommended operating conditions, dc operating conditions, and capacitance for 2.5-v flex 10ke devices. t o t e s t s y s t e m c 1 ( i n c l u d e s j i g c a p a c i t a n c e ) d e v i c e i n p u t r i s e a n d f a l l t i m e s < 3 n s d e v i c e o u t p u t 7 0 3 w 8 . 0 6 k w [ 4 8 1 ] w [ 4 8 1 ] w v c c i o power supply transients can affect ac measurements. simultaneous transitions o f m ultiple outputs should be avoided fo r a ccurate measurement. threshold tests must not be per formed under ac conditions. large-amplitude, fast-ground-current transients normally occur as the device outputs discharge the load capacitances. when these transients ow through the parasitic inductance between the device ground pin and the test system ground, signi cant reductions in obser vable noise immunity can result. numbers in brackets are for 2.5-v devices or outputs. numbers without brackets are for 3.3-v devices or outputs. table 19. flex 10ke 2.5-v device absolute maximum ratings note (1) symbol parameter conditions min max unit v ccint supply voltage with respect to ground (2) ?.5 3.6 v v ccio ?.5 4.6 v v i dc input voltage ?.0 5.75 v i out dc output current, per pin ?5 25 ma t stg storage temperature no bias ?5 150 ?c t amb ambient temperature under bias ?5 135 ?c t j junction temperature pqfp, tqfp, and bga packages, under bias 135 ?c ceramic pga packages, under bias 150 ?c
48 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 20. 2.5-v epf10k50e & epf10k200e device reco mmended operating conditions symbol parameter conditions min max unit v ccint supply voltage for internal logic and input buffers (3) , (4) 2.30 (2.30) 2.70 (2.70) v v ccio supply voltage for output buffers, 3.3-v operation (3) , (4) 3.00 (3.00) 3.60 (3.60) v supply voltage for output buffers, 2.5-v operation (3) , (4) 2.30 (2.30) 2.70 (2.70) v v i input voltage (5) ?.5 5.75 v v o output voltage 0 v ccio v t a ambient temperature for commercial use 0 70 ?c for industrial use ?0 85 ?c t j operating temperature for commercial use 0 85 ?c for industrial use ?0 100 ?c t r input rise time 40 ns t f input fall time 40 ns table 21. 2.5-v epf10k30e, epf10k50s, epf10k100e, EPF10K130E & epf10k200s device reco mmended operating conditions symbol parameter conditions min max unit v ccint supply voltage for internal logic and input buffers (3) , (4) 2.375 (2.375) 2.625 (2.625) v v ccio supply voltage for output buffers, 3.3-v operation (3) , (4) 3.00 (3.00) 3.60 (3.60) v supply voltage for output buffers, 2.5-v operation (3) , (4) 2.375 (2.375) 2.625 (2.625) v v i input voltage (5) ?.5 5.75 v v o output voltage 0 v ccio v t a ambient temperature for commercial use 0 70 ?c for industrial use ?0 85 ?c t j operating temperature for commercial use 0 85 ?c for industrial use ?0 100 ?c t r input rise time 40 ns t f input fall time 40 ns
altera corporation 49 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 22. flex 10ke 2.5-v d evice dc operating conditions notes (6) , (7) symbol parameter conditions min typ max unit v ih high-level input voltage 1.7, 0.5 v ccio (8) 5.75 v v il low-level input voltage ?.5 0.8, 0.3 v ccio (8) v v oh 3.3-v high-level ttl output voltage i oh = ? ma dc, v ccio = 3.00 v (9) 2.4 v 3.3-v high-level cmos output voltage i oh = ?.1 ma dc, v ccio = 3.00 v (9) v ccio ? 0.2 v 3.3-v high-level pci output voltage i oh = ?.5 ma dc, v ccio = 3.00 to 3.60 v (9) 0.9 v ccio v 2.5-v high-level output voltage i oh = ?.1 ma dc, v ccio = 2.30 v (9) 2.1 v i oh = ? ma dc, v ccio = 2.30 v (9) 2.0 v i oh = ? ma dc, v ccio = 2.30 v (9) 1.7 v v ol 3.3-v low-level ttl output voltage i ol = 12 ma dc, v ccio = 3.00 v (9) 0.45 v 3.3-v low-level cmos output voltage i ol = 0.1 ma dc, v ccio = 3.00 v (10) 0.2 v 3.3-v low-level pci output voltage i ol = 1.5 ma dc, v ccio = 3.00 to 3.60 v (10) 0.1 v ccio v 2.5-v low-level output voltage i ol = 0.1 ma dc, v ccio = 2.30 v (10) 0.2 v i ol = 1 ma dc, v ccio = 2.30 v (10) 0.4 v i ol = 2 ma dc, v ccio = 2.30 v (10) 0.7 v i i input pin leakage current v i = 5.3 to ?.3 v ?0 10 ? i oz tri-stated i/o pin leakage current v o = 5.3 to ?.3 v ?0 10 ? i cc0 v cc supply current (standby) v i = ground, no load, no toggling inputs 5 ma v i = ground, no load, no toggling inputs (11) 10 ma r conf value of i/o pin pull-up resistor before and during configuration v ccio = 3.0 v (12) 20 50 k w v ccio = 2.3 v (12) 30 80 k w
50 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation n otes to tables: (1) see the operating requirements for altera devices data sheet . (2) minimum dc input voltage is ?.5 v. during transitions, the inputs may undershoot to ?.0 v for input currents less than 100 ma and periods shorter than 20 ns. (3) numbers in parentheses are for industrial-temperature-range devices. (4) maximum v cc rise time is 100 ms, and v cc must rise monotonically. (5) all pins, including dedicated inputs, clock, i/o, and jtag pins, may be driven before v ccint and v ccio are powered. (6) typical values are for t a = 25 c, v ccint = 2.5 v, and v ccio = 2.5 v or 3.3 v. (7) these values are specified under the flex 10ke recommended operating conditions shown i n table 20 on page 48 . (8) the flex 10ke input buffers are compatible with 2.5-v, 3.3-v ( lvttl and lvcmos ) , and 5.0-v ttl a nd cmos signals. additionally, the input buffers are 3.3-v pci compliant when v cc io and v cc int meet the relationship shown in figure 22 . (9) the i oh parameter refers to high-level ttl, pci, or cmos output current. (10) the i ol parameter refers to low-level ttl, pci, or cmos output current. this parameter applies to open-drain pins as well as output pins. (11) this parameter applies to -1 speed grade commercial temperature devices and -2 speed grade industrial temperature devices. (12) pin pull-up resistance values will be lower if the pin is driven higher than v ccio by an external source. (13) capacitance is sample-tested only. table 23. flex 10ke d evice capacitance note (13) symbol parameter conditions min max unit c in input capacitance v in = 0 v, f = 1.0 mhz 10 pf c inclk input capacitance on dedicated clock pin v in = 0 v, f = 1.0 mhz 12 pf c out output capacitance v out = 0 v, f = 1.0 mhz 10 pf
altera corporation 51 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet figure 22 shows the required relationship between v ccio and v ccint for 3.3-v pci compliance. figure 22. relationship between v cc io & v cc int for 3.3-v pci compliance figure 23 shows the typical output drive characteristics of flex 10ke devices with 3.3-v and 2.5-v v ccio . the output driver is compliant to the 3.3-v pci local bus specification , revision 2.2 (when vccio pins are connected to 3.3 v ). flex 10ke devices with a -1 speed grade also comply with the drive strength requirements of the pci local bus specification , revision 2.2 (when vccint pins are powered with a minimum supply of 2.375 v, and vccio pins are connected to 3.3 v). therefore, these devices can be used in open 5.0-v pci systems. 3 . 0 3 . 1 3 . 3 v c c i o i o 3 . 6 2 . 3 2 . 5 2 . 7 v c c i n t i i ( v ) ( v ) p c i - c o m p l i a n t r e g i o n
52 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation figure 23. output drive characteristics of flex 10ke devices t im in g model the continuous, high-performance fasttrack interconnect routing resources ensure predictable performance and accurate simulation and timing analysis. this predictable performance contrasts with that of fpgas, which use a segmented connection scheme and therefore have unpredictable performance. device performance can be estimated by following the signal path from a source, through the interconnect, to the destination. for example, the registered performance between two les on the same row can be calculated by adding the following parameters: n le register clock-to-output delay ( t co ) n interconnect delay ( t samerow ) n le look-up table delay ( t lut ) n le register setup time ( t su ) the routing delay depends on the placement of the source and destination les. a more complex registered path may involve multiple combinatorial les between the source and destination les. timing simulation and delay prediction are available with the max+plus ii simulator and timing analyzer, or with industry- standard eda tools. the simulator offers both pre-synthesis functional simulation to evaluate logic design accuracy and post-synthesis timing simulation with 0.1-ns resolution. the timing analyzer provides point- to-point timing delay information, setup and hold time analysis, and device-wide performance analysis. v o o u t p u t v o l t a g e ( v ) i o l i o h i o h v v v c c i n t = 2 . 5 v c c i o = 2 . 5 r o o m t e m p e r a t u r e v v v c c i n t = 2 . 5 v c c i o = 3 . 3 r o o m t e m p e r a t u r e 1 2 3 1 0 2 0 3 0 5 0 6 0 4 0 7 0 8 0 9 0 v o o u t p u t v o l t a g e ( v ) 1 2 3 1 0 2 0 3 0 5 0 6 0 4 0 7 0 8 0 9 0 i o l o t y p i c a l i o u t p u t c u r r e n t ( m a ) o t y p i c a l i o u t p u t c u r r e n t ( m a )
altera corporation 53 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet figure 24 shows the overall timing model, which maps the possible paths to and from the various elements of the flex 10ke device. figure 24. flex 10ke device t iming model figures 25 through 28 show the delays that correspond to various paths and functions within the le, ioe, eab, and bidirectional timing models. figure 25. flex 10ke device le t iming model d e d i c a t e d c l o c k / i n p u t i n t e r c o n n e c t i / o e l e m e n t l o g i c e l e m e n t e m b e d d e d a r r a y b l o c k t c g e n r t c o t c o m b t s u t h t p r e t c l r r e g i s t e r d e l a y s l u t d e l a y t l u t t r l u t t c l u t c a r r y c h a i n d e l a y c a r r y - i n c a s c a d e - i n d a t a - o u t t c g e n t c i c o p a c k e d r e g i s t e r d e l a y t p a c k e d r e g i s t e r c o n t r o l d e l a y t c t e n d a t a - i n c o n t r o l - i n t c a s c c a s c a d e - o u t c a r r y - o u t t l a b c a r r y t l a b c a s c
54 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation figure 26. flex 10ke device ioe t iming model figure 27. flex 10ke device eab t iming model d a t a - i n i / o r e g i s t e r d e l a y s t i o c o t i o c o m b t i o s u t i o h t i o c l r o u t p u t d a t a d e l a y t i o d i / o e l e m e n t c o n t o l d e l a y t i o c i n p u t r e g i s t e r d e l a y t i n r e g o u t p u t d e l a y s t o d 1 t o d 2 t o d 3 t x z t z x 1 t z x 2 t z x 3 i / o r e g i s t e r f e e d b a c k d e l a y t i o f d i n p u t d e l a y t i n c o m b c l o c k e n a b l e c l e a r d a t a f e e d b a c k i n t o f a s t t r a c k i n t e r c o n n e c t c l o c k o u t p u t e n a b l e e a b d a t a i n p u t d e l a y s t e a b d a t a 1 t e a b d a t a 2 d a t a - i n w r i t e e n a b l e i n p u t d e l a y s t e a b w e 1 t e a b w e 2 e a b c l o c k d e l a y t e a b c l k i n p u t r e g i s t e r d e l a y s t e a b c o t e a b b y p a s s t e a b s u t e a b h t e a b c h t e a b c l t e a b r e 1 t e a b r e 2 r a m / r o m b l o c k d e l a y s t a a t r p t r a s u t r a h t d d t w p t w d s u t w d h t w a s u t w a h t w o o u t p u t r e g i s t e r d e l a y s t e a b c o t e a b b y p a s s t e a b s u t e a b h t e a b c h t e a b c l t e a b o u t a d d r e s s w e i n p u t r e g i s t e r c l o c k o u t p u t r e g i s t e r c l o c k d a t a - o u t e a b o u t p u t d e l a y r e a d e n a b l e i n p u t d e l a y s r e
altera corporation 55 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet figure 28. synchronous bidirectional pin external t iming model tables 24 through 28 describe the flex 10ke device internal timing parameters. tables 29 through 31 describe the flex 10ke external timing parameters and their symbols. detailed timing information for these devices will be released as it is available. p r n c l r n d q p r n c l r n d q p r n c l r n d q d e d i c a t e d c l o c k b i d i r e c t i o n a l p i n o u t p u t r e g i s t e r t i n s u b i d i r t o u t c o b i d i r t x z b i d i r t z x b i d i r t i n h b i d i r o e r e g i s t e r i n p u t r e g i s t e r table 24. le timing microparameters (part 1 of 2) note (1) symbol parameter conditions t lut lut delay for data-in t clut lut delay for carry-in t rlut lut delay for le register feedback t packed data-in to packed register delay t en le register enable delay t cico carry-in to carry-out delay t cgen data-in to carry-out delay t cgenr le register feedback to carry-out delay t casc cascade-in to cascade-out delay t c le register control signal delay t co le register clock-to-output delay t comb combinatorial delay t su le register setup time for data and enable signals before clock; le register recovery time after asynchronous clear, preset, or load t h le register hold time for data and enable signals after clock t pre le register preset delay
56 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation t clr le register clear delay t ch minimum clock high time from clock pin t cl minimum clock low time from clock pin table 25. ioe timing microparameters note (1) symbol parameter conditions t iod ioe data delay t ioc ioe register control signal delay t ioco ioe register clock-to-output delay t iocomb ioe combinatorial delay t iosu ioe register setup time for data and enable signals before clock; ioe register recovery time after asynchronous clear t ioh ioe register hold time for data and enable signals after clock t ioclr ioe register clear time t od1 output buffer and pad delay, slow slew rate = off, v ccio = v ccint c1 = 35 pf (2) t od2 output buffer and pad delay, slow slew rate = off, v ccio = low voltage c1 = 35 pf (3) t od3 output buffer and pad delay, slow slew rate = on c1 = 35 pf (4) t xz ioe output buffer disable delay t zx1 ioe output buffer enable delay, slow slew rate = off, v ccio = v ccint c1 = 35 pf (2) t zx2 ioe output buffer enable delay, slow slew rate = off, v ccio = low voltage c1 = 35 pf (3) t zx3 ioe output buffer enable delay, slow slew rate = on c1 = 35 pf (4) t inreg ioe input pad and buffer to ioe register delay t iofd ioe register feedback delay t incomb ioe input pad and buffer to fasttrack interconnect delay table 24. le timing microparameters (part 2 of 2) note (1) symbol parameter conditions
altera corporation 57 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 26. eab timing microparameters note (1) symbol parameter conditions t eabdata1 data or address delay to eab for combinatorial input t eabdata2 data or address delay to eab for registered input t eabwe1 write enable delay to eab for combinatorial input t eabwe2 write enable delay to eab for registered input t eabre1 read enable delay to eab for combinatorial input t eabre2 read enable delay to eab for registered input t eabclk eab register clock delay t eabco eab register clock-to-output delay t eabbypass bypass register delay t eabsu eab register setup time before clock t eabh eab register hold time after clock t eabclr eab register asynchronous clear time to output delay t eabch clock high time t eabcl clock low time t aa address access delay (including the read enable to output delay) t wp write pulse width t rp read pulse width t wdsu data setup time before falling edge of write pulse (5) t wdh data hold time after falling edge of write pulse (5) t wasu address setup time before rising edge of write pulse (5) t wah address hold time after falling edge of write pulse (5) t wasu address setup time before rising edge of write pulse t wah address hold time after falling edge of write pulse t rasu address setup time before rising edge of read pulse t rah address hold time after falling edge of read pulse t wo write enable to data output valid delay t dd data-in to data-out valid delay t eabout data-out delay
58 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 27. eab timing macroparameters notes (1) , (6) symbol parameter conditions t eabaa eab address access delay t eabrccomb eab asynchronous read cycle time t eabrcreg eab synchronous read cycle time t eabwp eab write pulse width t eabwccomb eab asynchronous write cycle time t eabwcreg eab synchronous write cycle time t eabdd eab data-in to data-out valid delay t eabdataco eab clock-to-output delay when using output registers t eabdatasu eab data/address setup time before clock when using input register t eabdatah eab data/address hold time after clock when using input register t eabwesu eab we setup time before clock when using input register t eabwesh eab we hold time after clock when using input register t eabwdsu eab data setup time before falling edge of write pulse when not using input registers t eabwdh eab data hold time after falling edge of write pulse when not using input registers t eabwasu eab address setup time before rising edge of write pulse when not using input registers t eabwah eab address hold time after falling edge of write pulse when not using input registers t eabwo eab write enable to data output valid delay
altera corporation 59 preliminary information flex 10ke embedded programmable logic family data sheet table 28. interconnect timing microparameters note (1) symbol parameter conditions t samelab routing delay for an le driving another le in the same lab t samerow routing delay for a row ioe, le, or eab driving a row ioe, le, or eab in the same row (7) t samecolumn routing delay for an le driving an ioe in the same column (7) t diffrow routing delay for a column ioe, le, or eab driving an le or eab in a different row (7) t tworows routing delay for a row ioe or eab driving an le or eab in a different row (7) t leperiph routing delay for an le driving a control signal of an ioe via the peripheral control bus (7) t labcarry routing delay for the carry-out signal of an le driving the carry-in signal of a different le in a different lab t labcasc routing delay for the cascade-out signal of an le driving the cascade-in signal of a different le in a different lab t din2ioe delay from dedicated input pin to ioe control input (7) t din2le delay from dedicated input pin to le or eab control input (7) t dclk2ioe delay from dedicated clock pin to ioe clock (7) t dclk2le delay from dedicated clock pin to le or eab clock (7) t din2data delay from dedicated input or clock to le or eab data (7) table 29. external reference timing parameters note (8) symbol parameter conditions t drr register-to-register delay via four les, three row interconnects, and four local interconnects (9) table 30. external timing parameters symbol parameter conditions t drr register-to-register delay via four les, three row interconnects, and four local interconnects (10) t insu setup time with global clock at ioe register t inh hold time with global clock at ioe register t outco clock-to-output delay with global clock at ioe register t pcisu setup time with global clock for registers used in pci designs (11) t pcih hold time with global clock for registers used in pci designs (11) t pcico clock-to-output delay with global clock for registers used in pci designs (11)
60 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation notes to tables : (1) microparameters are timing delays contributed by individual architectural elements. these parameters cannot be measured explicitly. (2) operating conditions: v ccio = 3.3 v 10 % for commercial or industrial use in flex 10ke devices (3) operating conditions: v ccio = 2.5 v 0.2 v for commercial or industrial use in flex 10ke devices. (4) operating conditions: v ccio = 2.5 v, 3.3 v, or 5.0 v. (5) because the ram in the eab is self-timed, this parameter can be ignored when the we signal is registered. (6) eab macroparameters are internal parameters that can simplify predicting the behavior of an eab at its boundary; these parameters are calculated by summing selected microparameters. (7) these parameters are worst-case values for typical applications. post-compilation timing simulation and timing analysis are required to determine actual worst-case performance. (8) external reference timing parameters are factory-tested, worst-case values specified by altera. a representative subset of signal paths is tested to approximate typical device applications. (9) contact altera applications for test circuit specifications and test conditions. (10) contact altera applications for test circuit specifications and test conditions. (11) this parameter is measured with the measurement and test conditions, including load, specified in the pci local bus specification, revision 2.2 . (12) these timing parameters are sample-tested only. table 31. external bidirectional timing parameters note (12) symbol parameter condition t insubidir setup time for bidirectional pins with global clock at same-row or same- column l e register t inhbidir hold time for bidirectional pins with global clock at same-row or same-column l e register t outcobidir clock-to-output delay for bidirectional pins with global clock at ioe register ci = 35 pf t xzbidir synchronous ioe output buffer disable delay ci = 35 pf t zxbidir synchronous ioe output buffer enable delay, slow slew rate = off ci = 35 pf
altera corporation 61 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet tables 32 through 38 show epf10k30e device internal and external timing parameters. table 32. epf10k30e device le timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t lut 0.6 0.8 1.1 ns t clut 0.5 0.6 0.8 ns t rlut 0.7 0.8 1.1 ns t packed 0.5 0.6 0.8 ns t en 0.6 0.7 0.9 ns t cico 0.2 0.2 0.3 ns t cgen 0.5 0.5 0.8 ns t cgenr 0.2 0.2 0.3 ns t casc 0.8 0.9 1.2 ns t c 0.5 0.6 0.8 ns t co 0.5 0.6 0.7 ns t comb 0.5 0.6 0.7 ns t su 0.5 0.6 0.8 ns t h 0.9 1.1 1.5 ns t pre 0.5 0.6 0.8 ns t clr 0.5 0.6 0.8 ns t ch 2.0 2.5 3.0 ns t cl 2.0 2.5 3.0 ns
62 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 33. epf10k30e device ioe timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t iod 2.4 2.8 3.8 ns t ioc 0.3 0.3 0.5 ns t ioco 0.2 0.2 0.3 ns t iocomb 0.5 0.6 0.8 ns t iosu 2.2 2.6 3.5 ns t ioh 0.5 0.6 0.8 ns t ioclr 0.2 0.2 0.3 ns t od1 1.1 1.3 1.8 ns t od2 0.6 0.9 1.6 ns t od3 3.0 3.5 4.8 ns t xz 1.1 1.3 1.8 ns t zx1 1.1 1.3 1.6 ns t zx2 0.6 0.9 1.6 ns t zx3 3.0 3.5 4.8 ns t inreg 5.0 5.9 8.0 ns t iofd 3.0 3.6 4.8 ns t incomb 3.0 3.6 4.8 ns
altera corporation 63 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 34. epf10k30e device eab internal microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabdata1 1.7 2.0 2.7 ns t eabdata2 0.6 0.7 0.9 ns t eabwe1 1.1 1.3 1.8 ns t eabwe2 0.4 0.4 0.6 ns t eabre1 0.8 0.9 1.2 ns t eabre2 0.4 0.4 0.6 ns t eabclk 0.0 0.0 0.0 ns t eabco 0.3 0.3 0.5 ns t eabbypass 0.5 0.6 0.8 ns t eabsu 0.9 1.0 1.4 ns t eabh 0.4 0.4 0.6 ns t eabclr 0.3 0.3 0.5 ns t aa 3.2 3.8 5.1 ns t wp 2.5 2.9 3.9 ns t rp 0.9 1.1 1.5 ns t wdsu 0.9 1.0 1.4 ns t wdh 0.1 0.1 0.2 ns t wasu 1.7 2.0 2.7 ns t wah 1.8 2.1 2.9 ns t rasu 3.1 3.7 5.0 ns t rah 0.2 0.2 0.3 ns t wo 2.5 2.9 3.9 ns t dd 2.5 2.9 3.9 ns t eabout 0.5 0.6 0.8 ns t eabch 1.5 2.0 2.5 ns t eabcl 1.5 2.0 2.5 ns
64 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 35. epf10k30e device eab internal timing macroparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabaa 6.4 7.6 10.2 ns t eabrccomb 6.4 7.6 10.2 ns t eabrcreg 4.4 5.1 7.0 ns t eabwp 2.5 2.9 3.9 ns t eabwccomb 6.0 7.0 9.5 ns t eabwcreg 6.8 7.8 10.6 ns t eabdd 5.7 6.7 9.0 ns t eabdataco 0.8 0.9 1.3 ns t eabdatasu 1.5 1.7 2.3 ns t eabdatah 0.0 0.0 0.0 ns t eabwesu 1.3 1.4 2.0 ns t eabweh 0.0 0.0 0.0 ns t eabwdsu 1.5 1.7 2.3 ns t eabwdh 0.0 0.0 0.0 ns t eabwasu 3.0 3.6 4.8 ns t eabwah 0.5 0.5 0.8 ns t eabwo 5.1 6.0 8.1 ns
altera corporation 65 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 36. epf10k30e device interconnect timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t din2ioe 4.1 4.6 5.9 ns t din2le 0.9 1.0 1.3 ns t din2data 1.8 1.9 2.3 ns t dclk2ioe 3.9 4.6 6.2 ns t dclk2le 0.9 1.0 1.3 ns t samelab 0.1 0.1 0.2 ns t samerow 1.3 1.3 1.8 ns t samecolumn 0.7 0.8 1.5 ns t diffrow 2.0 2.1 3.3 ns t tworows 3.3 3.4 5.1 ns t leperiph 3.8 4.1 5.3 ns t labcarry 0.1 0.1 0.2 ns t labcasc 0.3 0.3 0.5 ns table 37. epf10k30e external ti ming pa rameters notes (1) , (2) symbol spe ed grade unit -1 -2 -3 min max min max min max t drr 8.5 10.0 13.5 ns t insu (3) 3.0 3.6 4.8 ns t inh (3) 0.0 0.0 0.0 ns t outco (3) 2.0 3.5 2.0 4.5 2.0 7.1 ns t insu (4) 2.0 2.6 ns t inh (4) 0.0 0.0 ns t outco (4) 0.5 2.5 0.5 3.5 ns t pcisu 3.0 4.2 6.4 ns t pcih 0.0 0.0 0.0 ns t pcico 2.0 6.0 2.0 7.5 2.0 10.2 ns
66 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation notes to tables: (1) all timing parameters are described in tables 24 through 31 in this data sheet. (2) th ese parameter s are s pecified by characterization . (3) this parameter is measured without the use of the clocklock or clockboost circuits. (4) this parameter is measured with the use of the clocklock or clockboost circuits. table 38. epf10k30e external bidirectional ti ming pa rameters notes (1) , (2) symbol spe ed grade unit -1 -2 -3 min max min max min max t insubidir 1.5 2.2 3.6 ns t inhbidir 0.0 0.0 0.0 ns t outcobidir (3) 2.0 3.5 2.0 4.5 2.0 7.1 ns t xzbidir (3) 2.0 5.8 2.0 6.3 2.0 8.0 ns t zxbidir (3) 2.0 4.7 2.0 5.3 2.0 7.2 ns t outcobidir (4) 0.5 2.5 0.5 3.5 ns t xzbidir (4) 0.5 5.3 0.5 5.8 ns t zxbidir (4) 0.5 4.2 0.5 4.8 ns
altera corporation 67 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet tables 39 through 45 show epf10k50e device internal and external timing parameters. table 39. epf10k50e device le timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t lut 0.6 0.8 1.1 ns t clut 0.5 0.6 0.8 ns t rlut 0.7 0.8 1.1 ns t packed 0.5 0.6 0.8 ns t en 0.6 0.7 0.9 ns t cico 0.2 0.2 0.3 ns t cgen 0.5 0.5 0.8 ns t cgenr 0.2 0.2 0.3 ns t casc 0.8 0.9 1.2 ns t c 0.5 0.6 0.8 ns t co 0.5 0.6 0.7 ns t comb 0.5 0.6 0.7 ns t su 0.5 0.6 0.8 ns t h 0.9 1.1 1.5 ns t pre 0.5 0.6 0.8 ns t clr 0.5 0.6 0.8 ns t ch 2.0 2.5 3.0 ns t cl 2.0 2.5 3.0 ns
68 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 40. epf10k50e device ioe timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t iod 2.4 2.8 3.8 ns t ioc 0.3 0.3 0.5 ns t ioco 0.2 0.2 0.3 ns t iocomb 0.5 0.6 0.8 ns t iosu 2.2 2.6 3.5 ns t ioh 0.5 0.6 0.8 ns t ioclr 0.2 0.2 0.3 ns t od1 1.1 1.3 1.8 ns t od2 0.6 0.9 1.6 ns t od3 3.0 3.5 4.8 ns t xz 1.1 1.3 1.8 ns t zx1 1.1 1.3 1.6 ns t zx2 0.6 0.9 1.6 ns t zx3 3.0 3.5 4.8 ns t inreg 5.0 5.9 8.0 ns t iofd 3.0 3.6 4.8 ns t incomb 3.0 3.6 4.8 ns
altera corporation 69 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 41. epf10k50e device eab internal microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabdata1 1.7 2.0 2.7 ns t eabdata2 0.6 0.7 0.9 ns t eabwe1 1.1 1.3 1.8 ns t eabwe2 0.4 0.4 0.6 ns t eabre1 0.8 0.9 1.2 ns t eabre2 0.4 0.4 0.6 ns t eabclk 0.0 0.0 0.0 ns t eabco 0.3 0.3 0.5 ns t eabbypass 0.5 0.6 0.8 ns t eabsu 0.9 1.0 1.4 ns t eabh 0.4 0.4 0.6 ns t eabclr 0.3 0.3 0.5 ns t aa 3.2 3.8 5.1 ns t wp 2.5 2.9 3.9 ns t rp 0.9 1.1 1.5 ns t wdsu 0.9 1.0 1.4 ns t wdh 0.1 0.1 0.2 ns t wasu 1.7 2.0 2.7 ns t wah 1.8 2.1 2.9 ns t rasu 3.1 3.7 5.0 ns t rah 0.2 0.2 0.3 ns t wo 2.5 2.9 3.9 ns t dd 2.5 2.9 3.9 ns t eabout 0.5 0.6 0.8 ns t eabch 1.5 2.0 2.5 ns t eabcl 1.5 2.0 2.5 ns
70 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 42. epf10k50e device eab internal timing macroparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabaa 6.4 7.6 10.2 ns t eabrccomb 6.4 7.6 10.2 ns t eabrcreg 4.4 5.1 7.0 ns t eabwp 2.5 2.9 3.9 ns t eabwccomb 6.0 7.0 9.5 ns t eabwcreg 6.8 7.8 10.6 ns t eabdd 5.7 6.7 9.0 ns t eabdataco 0.8 0.9 1.3 ns t eabdatasu 1.5 1.7 2.3 ns t eabdatah 0.0 0.0 0.0 ns t eabwesu 1.3 1.4 2.0 ns t eabweh 0.0 0.0 0.0 ns t eabwdsu 1.5 1.7 2.3 ns t eabwdh 0.0 0.0 0.0 ns t eabwasu 3.0 3.6 4.8 ns t eabwah 0.5 0.5 0.8 ns t eabwo 5.1 6.0 8.1 ns
altera corporation 71 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 43. epf10k50e device interconnect timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t din2ioe 4.6 5.1 6.4 ns t din2le 0.9 1.0 1.3 ns t din2data 1.5 1.9 2.3 ns t dclk2ioe 3.9 4.6 6.2 ns t dclk2le 0.9 1.0 1.3 ns t samelab 0.1 0.1 0.2 ns t samerow 1.3 1.3 1.8 ns t samecolumn 1.6 1.7 2.4 ns t diffrow 2.9 3.0 4.2 ns t tworows 4.2 4.3 6.0 ns t leperiph 4.3 4.6 5.8 ns t labcarry 0.1 0.1 0.2 ns t labcasc 0.3 0.3 0.5 ns table 44. epf10k50e external timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t drr 8.5 10.0 13.5 ns t insu 3.0 3.6 4.8 ns t inh 0.0 0.0 0.0 ns t outco 2.0 4.6 2.0 5.4 2.0 8.0 ns t pcisu 3.0 4.2 6.4 ns t pcih 0.0 0.0 0.0 ns t pcico 2.0 6.0 2.0 7.7 2.0 10.5 ns
72 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation notes to tables: (1) all timing parameters are described in tables 24 through 31 in this data sheet. (2) th ese p arameter s are s pecified by characterization. tables 46 through 52 show epf10k100e device internal and external timing parameters. table 45. epf10k50e external bidirectional timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t insubidir 2.7 3.4 4.8 ns t inhbidir 0.0 0.0 0.0 ns t outcobidir 2.0 4.6 2.0 5.4 2.0 8.2 ns t xzbidir 2.0 6.3 2.0 6.8 2.0 8.5 ns t zxbidir 2.0 5.2 2.0 5.8 2.0 7.7 ns table 46. epf10k100e device le timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t lut 0.6 0.8 1.1 ns t clut 0.5 0.6 0.8 ns t rlut 0.7 0.8 1.1 ns t packed 0.5 0.6 0.8 ns t en 0.6 0.7 0.9 ns t cico 0.2 0.2 0.3 ns t cgen 0.5 0.5 0.8 ns t cgenr 0.2 0.2 0.3 ns t casc 0.8 0.9 1.2 ns t c 0.5 0.6 0.8 ns t co 0.5 0.6 0.7 ns t comb 0.5 0.6 0.7 ns t su 0.5 0.6 0.8 ns t h 0.9 1.1 1.5 ns t pre 0.5 0.6 0.8 ns t clr 0.5 0.6 0.8 ns t ch 2.0 2.5 3.0 ns t cl 2.0 2.5 3.0 ns
altera corporation 73 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 47. epf10k100e device ioe timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t iod 2.4 2.8 3.8 ns t ioc 0.3 0.3 0.5 ns t ioco 0.2 0.2 0.3 ns t iocomb 0.5 0.6 0.8 ns t iosu 2.2 2.6 3.5 ns t ioh 0.5 0.6 0.8 ns t ioclr 0.2 0.2 0.3 ns t od1 1.1 1.3 1.8 ns t od2 0.6 0.9 1.6 ns t od3 3.0 3.5 4.8 ns t xz 1.1 1.3 1.8 ns t zx1 1.1 1.3 1.6 ns t zx2 0.6 0.9 1.6 ns t zx3 3.0 3.5 4.8 ns t inreg 5.0 5.9 8.0 ns t iofd 3.0 3.6 4.8 ns t incomb 3.0 3.6 4.8 ns
74 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 48. epf10k100e device eab internal microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabdata1 1.7 2.0 2.7 ns t eabdata2 0.6 0.7 0.9 ns t eabwe1 1.1 1.3 1.8 ns t eabwe2 0.4 0.4 0.6 ns t eabre1 0.8 0.9 1.2 ns t eabre2 0.4 0.4 0.6 ns t eabclk 0.0 0.0 0.0 ns t eabco 0.3 0.3 0.5 ns t eabbypass 0.5 0.6 0.8 ns t eabsu 0.9 1.0 1.4 ns t eabh 0.4 0.4 0.6 ns t eabclr 0.3 0.3 0.5 ns t aa 3.2 3.8 5.1 ns t wp 2.5 2.9 3.9 ns t rp 0.9 1.1 1.5 ns t wdsu 0.9 1.0 1.4 ns t wdh 0.1 0.1 0.2 ns t wasu 1.7 2.0 2.7 ns t wah 1.8 2.1 2.9 ns t rasu 3.1 3.7 5.0 ns t rah 0.2 0.2 0.3 ns t wo 2.5 2.9 3.9 ns t dd 2.5 2.9 3.9 ns t eabout 0.5 0.6 0.8 ns t eabch 1.5 2.0 2.5 ns t eabcl 1.5 2.0 2.5 ns
altera corporation 75 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 49. epf10k100e device eab internal timing macroparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabaa 6.4 7.6 10.2 ns t eabrccomb 6.4 7.6 10.2 ns t eabrcreg 4.4 5.1 7.0 ns t eabwp 2.5 2.9 3.9 ns t eabwccomb 6.0 7.0 9.5 ns t eabwcreg 6.8 7.8 10.6 ns t eabdd 5.7 6.7 9.0 ns t eabdataco 0.8 0.9 1.3 ns t eabdatasu 1.5 1.7 2.3 ns t eabdatah 0.0 0.0 0.0 ns t eabwesu 1.3 1.4 2.0 ns t eabweh 0.0 0.0 0.0 ns t eabwdsu 1.5 1.7 2.3 ns t eabwdh 0.0 0.0 0.0 ns t eabwasu 3.0 3.6 4.8 ns t eabwah 0.5 0.5 0.8 ns t eabwo 5.1 6.0 8.1 ns
76 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 50. epf10k100e device interconnect timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t din2ioe 3.5 3.9 4.9 ns t din2le 0.6 0.6 0.9 ns t din2data 2.0 2.1 2.9 ns t dclk2ioe 1.7 2.0 2.8 ns t dclk2le 0.6 0.6 0.9 ns t samelab 0.1 0.1 0.2 ns t samerow 1.7 1.8 1.7 ns t samecolumn 1.2 1.1 0.8 ns t diffrow 2.9 2.9 2.5 ns t tworows 4.6 4.7 4.2 ns t leperiph 4.3 4.9 5.9 ns t labcarry 0.1 0.1 0.2 ns t labcasc 0.3 0.3 0.5 ns table 51. epf10k100e external timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t drr 10.0 12.0 16.0 ns t insu (3) 3.1 3.7 4.7 ns t inh (3) 0.0 0.0 0.0 ns t outco (3) 2.0 3.7 2.0 4.4 2.0 6.3 ns t insu (4) 2.1 2.7 ns t inh (4) 0.0 0.0 ns t outco (4) 2.0 2.7 0.5 3.4 ns t pcisu 3.0 6.2 ns t pcih 0.0 0.0 ns t pcico 2.0 6.0 6.9 ns
altera corporation 77 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet notes to tables: (1) all timing parameters are described in tables 24 through 31 in this data sheet. (2) th ese p arameter s are s pecified by characterization. (3) this parameter is measured without the use of the clocklock or clockboost circuits. (4) this parameter is measured with the use of the clocklock or clockboost circuits. table 52. epf10k100e external bidirectional timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t insubidir 2.5 3.3 4.4 ns t inhbidir 0.0 0.0 0.0 ns t outcobidir (3) 2.0 3.7 2.0 4.4 2.0 6.3 ns t xzbidir (3) 2.0 5.2 2.0 6.1 2.0 8.3 ns t zxbidir (3) 2.0 4.7 2.0 5.6 2.0 8.1 ns t outcobidir (4) 0.5 2.7 0.5 3.4 ns t xzbidir (4) 0.5 4.2 0.5 5.1 ns t zxbidir (4) 0.5 3.7 0.5 4.6 ns
78 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation tables 53 through 59 show EPF10K130E device internal an d external timing parameters. table 53. EPF10K130E device le timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t lut 0.6 0.8 1.1 ns t clut 0.5 0.6 0.8 ns t rlut 0.7 0.8 1.1 ns t packed 0.5 0.6 0.8 ns t en 0.6 0.7 0.9 ns t cico 0.2 0.2 0.3 ns t cgen 0.5 0.5 0.8 ns t cgenr 0.2 0.2 0.3 ns t casc 0.8 0.9 1.2 ns t c 0.5 0.6 0.8 ns t co 0.5 0.6 0.7 ns t comb 0.5 0.6 0.7 ns t su 0.5 0.6 0.8 ns t h 0.9 1.1 1.5 ns t pre 0.5 0.6 0.8 ns t clr 0.5 0.6 0.8 ns t ch 2.0 2.5 3.0 ns t cl 2.0 2.5 3.0 ns
altera corporation 79 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 54. EPF10K130E device ioe timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t iod 2.4 2.8 3.8 ns t ioc 0.3 0.3 0.5 ns t ioco 0.2 0.2 0.3 ns t iocomb 0.5 0.6 0.8 ns t iosu 2.2 2.6 3.5 ns t ioh 0.5 0.6 0.8 ns t ioclr 0.2 0.2 0.3 ns t od1 1.1 1.3 1.8 ns t od2 0.6 0.9 1.6 ns t od3 3.0 3.5 4.8 ns t xz 1.1 1.3 1.8 ns t zx1 1.1 1.3 1.6 ns t zx2 0.6 0.9 1.6 ns t zx3 3.0 3.5 4.8 ns t inreg 5.0 5.9 8.0 ns t iofd 3.0 3.6 4.8 ns t incomb 3.0 3.6 4.8 ns
80 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 55. EPF10K130E device eab internal microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabdata1 1.7 2.0 2.7 ns t eabdata2 0.6 0.7 0.9 ns t eabwe1 1.1 1.3 1.8 ns t eabwe2 0.4 0.4 0.6 ns t eabre1 0.8 0.9 1.2 ns t eabre2 0.4 0.4 0.6 ns t eabclk 0.0 0.0 0.0 ns t eabco 0.3 0.3 0.5 ns t eabbypass 0.5 0.6 0.8 ns t eabsu 0.9 1.0 1.4 ns t eabh 0.4 0.4 0.6 ns t eabclr 0.3 0.3 0.5 ns t aa 3.2 3.8 5.1 ns t wp 2.5 2.9 3.9 ns t rp 0.9 1.1 1.5 ns t wdsu 0.9 1.0 1.4 ns t wdh 0.1 0.1 0.2 ns t wasu 1.7 2.0 2.7 ns t wah 1.8 2.1 2.9 ns t rasu 3.1 3.7 5.0 ns t rah 0.2 0.2 0.3 ns t wo 2.5 2.9 3.9 ns t dd 2.5 2.9 3.9 ns t eabout 0.5 0.6 0.8 ns t eabch 1.5 2.0 2.5 ns t eabcl 1.5 2.0 2.5 ns
altera corporation 81 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 56. EPF10K130E device eab internal timing macroparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabaa 6.4 7.6 10.2 ns t eabrccomb 6.4 7.6 10.2 ns t eabrcreg 4.4 5.1 7.0 ns t eabwp 2.5 2.9 3.9 ns t eabwccomb 6.0 7.0 9.5 ns t eabwcreg 6.8 7.8 10.6 ns t eabdd 5.7 6.7 9.0 ns t eabdataco 0.8 0.9 1.3 ns t eabdatasu 1.5 1.7 2.3 ns t eabdatah 0.0 0.0 0.0 ns t eabwesu 1.3 1.4 2.0 ns t eabweh 0.0 0.0 0.0 ns t eabwdsu 1.5 1.7 2.3 ns t eabwdh 0.0 0.0 0.0 ns t eabwasu 3.0 3.6 4.8 ns t eabwah 0.5 0.5 0.8 ns t eabwo 5.1 6.0 8.1 ns
82 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 57. EPF10K130E device interconnect timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t din2ioe 3.9 4.3 5.3 ns t din2le 0.6 0.6 0.9 ns t din2data 2.0 2.1 2.9 ns t dclk2ioe 1.7 2.0 2.8 ns t dclk2le 0.6 0.6 0.9 ns t samelab 0.1 0.1 0.2 ns t samerow 1.7 1.8 1.7 ns t samecolumn 1.6 1.5 1.4 ns t diffrow 3.3 3.3 3.1 ns t tworows 5.0 5.1 4.8 ns t leperiph 4.7 5.3 6.3 ns t labcarry 0.1 0.1 0.2 ns t labcasc 0.3 0.3 0.5 ns table 58. EPF10K130E external timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t drr 10.0 12.0 16.0 ns t insu (3) 3.1 3.7 4.7 ns t inh (3) 0.0 0.0 0.0 ns t outco (3) 2.0 3.7 2.0 4.4 2.0 6.3 ns t insu (4) 2.1 2.7 ns t inh (4) 0.0 0.0 ns t outco (4) 2.0 2.7 0.5 3.4 ns t pcisu 3.0 6.2 ns t pcih 0.0 0.0 ns t pcico 2.0 6.0 2.0 6.9 ns
altera corporation 83 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet notes to tables: (1) all timing parameters are described in tables 24 through 31 in this data sheet. (2) th ese p arameter s are s pecified by characterization. (3) this parameter is measured without the use of the clocklock or clockboost circuits. (4) this parameter is measured with the use of the clocklock or clockboost circuits. table 59. EPF10K130E external bidirectional timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t insubidir 2.5 3.3 4.4 ns t inhbidir 0.0 0.0 0.0 ns t outcobidir (3) 2.0 3.7 2.0 4.4 2.0 6.3 ns t xzbidir (3) 4.2 4.9 6.8 ns t zxbidir (3) 3.7 4.5 6.6 ns t outcobidir (4) 0.5 2.7 0.5 3.4 ns t xzbidir (4) 0.5 4.2 0.5 5.1 ns t zxbidir (4) 0.5 3.7 0.5 4.6 ns
84 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation tables 60 through 66 show epf10k200e device internal and external timing parameters. table 60. epf10k200e device le timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t lut 0.7 0.8 1.2 ns t clut 0.4 0.5 0.6 ns t rlut 0.6 0.7 0.9 ns t packed 0.3 0.3 0.5 ns t en 0.4 0.5 0.6 ns t cico 0.2 0.2 0.3 ns t cgen 0.4 0.4 0.6 ns t cgenr 0.2 0.2 0.3 ns t casc 0.7 0.8 1.2 ns t c 0.5 0.6 0.8 ns t co 0.5 0.6 0.8 ns t comb 0.4 0.6 0.8 ns t su 0.4 0.6 0.7 ns t h 0.9 1.1 1.5 ns t pre 0.5 0.6 0.8 ns t clr 0.5 0.6 0.8 ns t ch 2.0 2.5 3.0 ns t cl 2.0 2.5 3.0 ns
altera corporation 85 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 61. epf10k200e device ioe timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t iod 2.7 3.3 4.4 ns t ioc 0.3 0.3 0.5 ns t ioco 1.6 1.9 2.6 ns t iocomb 0.5 0.6 0.8 ns t iosu 0.8 0.9 1.2 ns t ioh 0.7 0.8 1.1 ns t ioclr 0.2 0.2 0.3 ns t od1 0.6 0.7 0.9 ns t od2 0.1 0.2 0.7 ns t od3 2.5 3.0 3.9 ns t xz 2.1 2.5 3.3 ns t zx1 2.1 2.5 3.3 ns t zx2 1.6 2.0 3.1 ns t zx3 4.0 4.8 6.3 ns t inreg 4.3 5.1 6.8 ns t iofd 0.5 0.6 0.8 ns t incomb 0.5 0.6 0.8 ns
86 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 62. epf10k200e device eab internal microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabdata1 2.0 2.4 3.2 ns t eabdata2 0.4 0.5 0.6 ns t eabwe1 1.4 1.7 2.3 ns t eabwe2 0.0 0.0 0.0 ns t eabre1 0.0 0.0 0.0 ns t eabre2 0.4 0.5 0.6 ns t eabclk 0.0 0.0 0.0 ns t eabco 0.8 0.9 1.2 ns t eabbypass 0.0 0.1 0.1 ns t eabsu 0.9 1.1 1.5 ns t eabh 0.4 0.5 0.6 ns t eabclr 0.8 0.9 1.2 ns t aa 3.1 3.7 4.9 ns t wp 3.3 4.0 5.3 ns t rp 0.9 1.1 1.5 ns t wdsu 0.9 1.1 1.5 ns t wdh 0.1 0.1 0.1 ns t wasu 1.3 1.6 2.1 ns t wah 2.1 2.5 3.3 ns t rasu 2.2 2.6 3.5 ns t rah 0.1 0.1 0.2 ns t wo 2.0 2.4 3.2 ns t dd 2.0 2.4 3.2 ns t eabout 0.0 0.1 0.1 ns t eabch 1.5 2.0 2.5 ns t eabcl 1.5 2.0 2.5 ns
altera corporation 87 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 63. epf10k200e device eab internal timing macroparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabaa 5.1 6.4 8.4 ns t eabrccomb 5.1 6.4 8.4 ns t eabrcreg 4.8 5.7 7.6 ns t eabwp 3.3 4.0 5.3 ns t eabwccomb 6.7 8.1 10.7 ns t eabwcreg 6.6 8.0 10.6 ns t eabdd 4.0 5.1 6.7 ns t eabdataco 0.8 1.0 1.3 ns t eabdatasu 1.3 1.6 2.1 ns t eabdatah 0.0 0.0 0.0 ns t eabwesu 0.9 1.1 1.5 ns t eabweh 0.4 0.5 0.6 ns t eabwdsu 1.5 1.8 2.4 ns t eabwdh 0.0 0.0 0.0 ns t eabwasu 3.0 3.6 4.7 ns t eabwah 0.4 0.5 0.7 ns t eabwo 3.4 4.4 5.8 ns
88 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 64. epf10k200e device interconnect timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t din2ioe 4.9 5.3 6.3 ns t din2le 0.6 0.6 0.9 ns t din2data 1.9 2.1 2.8 ns t dclk2ioe 1.7 2.0 2.8 ns t dclk2le 0.6 0.6 0.9 ns t samelab 0.1 0.1 0.2 ns t samerow 2.9 3.2 3.9 ns t samecolumn 3.3 3.5 4.6 ns t diffrow 6.2 6.7 8.5 ns t tworows 9.1 9.9 12.4 ns t leperiph 5.6 6.2 7.2 ns t labcarry 0.1 0.1 0.2 ns t labcasc 0.9 1.0 1.4 ns
altera corporation 89 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet notes to tables: (1) all timing parameters are described in tables 24 through 31 in this data sheet. (2) th ese parameter s are s pecified by characterization. (3) this parameter is measured without the use of the clocklock or clockboost circuits. (4) this parameter is measured with the use of the clocklock or clockboost circuits. table 65. epf10k200e external timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t drr 10.0 12.0 16.0 ns t insu (3) 3.1 3.7 4.7 ns t inh (3) 0.0 0.0 0.0 ns t outco (3) 2.0 3.7 2.0 4.4 2.0 6.3 ns t insu (4) 2.1 2.7 ns t inh (4) 0.0 0.0 ns t outco (4) 0.5 3.0 0.5 3.4 ns t pcisu 3.0 6.2 ns t pcih 0.0 0.0 ns t pcico 2.0 6.0 2.0 8.9 ns table 66. epf10k200e external bidirectional timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t insubdir (3) 2.5 3.3 4.4 ns t inhbidir (3) 0.0 0.0 0.0 ns t outcobidir (3) 2.0 3.7 2.0 4.4 2.0 6.3 ns t xzbidir (3) 2.0 5.2 2.0 6.1 2.0 8.3 ns t zxbidir (3) 2.0 4.7 2.0 5.6 2.0 8.1 ns t insubdir (4) 3.5 4.3 ns t inhbidir (4) 0.0 0.0 ns t outcobidir (4) 0.5 2.7 0.5 3.4 ns t xzbidir (4) 0.5 4.2 0.5 5.1 ns t zxbidir (4) 0.5 3.7 0.5 4.6 ns
90 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation tables 67 through 73 show epf10k100b device internal and external timing parameters. table 67. epf10k100b device le timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t lut 1.7 1.9 2.1 ns t clut 0.8 0.9 0.9 ns t rlut 1.3 1.4 1.6 ns t packed 0.6 0.7 0.8 ns t en 0.5 0.5 0.7 ns t cico 0.2 0.2 0.3 ns t cgen 0.5 0.5 0.7 ns t cgenr 0.5 0.5 0.7 ns t casc 0.6 0.6 0.8 ns t c 1.0 1.1 1.1 ns t co 0.6 0.6 0.8 ns t comb 0.5 0.6 0.8 ns t su 0.5 0.6 0.8 ns t h 1.5 1.6 2.0 ns t pre 0.6 0.7 0.8 ns t clr 0.6 0.7 0.8 ns t ch 2.0 2.5 3.0 ns t cl 2.0 2.5 3.0 ns
altera corporation 91 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 68. epf10k100b device ioe timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t iod 1.5 1.6 1.7 ns t ioc 0.3 0.3 0.4 ns t ioco 0.2 0.2 0.3 ns t iocomb 0.5 0.5 0.7 ns t iosu 1.2 1.3 1.6 ns t ioh 1.2 1.3 1.6 ns t ioclr 0.0 0.0 0.0 ns t od1 2.3 2.5 2.5 ns t od2 3.1 3.4 3.6 ns t od3 4.3 4.7 5.2 ns t xz 4.5 4.9 5.9 ns t zx1 4.5 4.9 5.9 ns t zx2 3.1 3.9 5.4 ns t zx3 6.5 7.1 8.6 ns t inreg 6.0 6.5 7.9 ns t iofd 2.8 3.1 3.7 ns t incomb 2.8 3.1 4.8 ns
92 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 69. epf10k100b device eab internal microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabdata1 3.2 3.5 4.2 ns t eabdata2 0.6 0.7 0.7 ns t eabwe1 1.3 1.4 1.7 ns t eabwe2 1.1 1.2 1.5 ns t eabclk 0.0 0.0 0.0 ns t eabco 1.0 1.1 1.3 ns t eabbypass 0.0 0.0 0.0 ns t eabsu 1.5 1.6 2.0 ns t eabh 0.1 0.1 0.1 ns t aa 3.2 3.8 5.1 ns t wp 3.4 3.7 4.5 ns t wdsu 0.1 0.1 0.1 ns t wdh 1.5 1.6 1.7 ns t wasu 1.6 1.7 2.1 ns t wah 0.9 1.0 1.2 ns t wo 2.8 3.1 3.6 ns t dd 2.8 3.1 3.6 ns t eabout 0.5 0.5 0.7 ns t eabch 2.0 2.5 3.0 ns t eabcl 3.4 3.7 4.5 ns
altera corporation 93 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 70. epf10k100b device eab internal timing macroparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t eabaa 7.5 8.1 9.9 ns t eabrccomb 7.5 8.1 9.9 ns t eabrcreg 5.3 5.7 7.0 ns t eabwp 3.4 3.7 4.5 ns t eabwccomb 5.9 6.4 7.8 ns t eabwcreg 8.6 9.4 11.2 ns t eabdd 6.5 7.1 8.5 ns t eabdataco 1.5 1.6 2.0 ns t eabdatasu 2.1 2.3 2.7 ns t eabdatah 0.0 0.0 0.0 ns t eabwesu 2.6 2.8 3.5 ns t eabweh 0.0 0.0 0.0 ns t eabwdsu 2.0 2.2 2.6 ns t eabwdh 0.0 0.0 0.0 ns t eabwasu 4.5 4.8 6.0 ns t eabwah 0.0 0.0 0.0 ns t eabwo 4.6 5.0 6.0 ns
94 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 71. epf10k100b device interconnect timing microparameters note (1) symbol speed grade unit -1 -2 -3 min max min max min max t din2ioe 4.8 4.9 5.5 ns t din2le 1.1 1.2 1.7 ns t din2data 1.5 1.4 1.9 ns t dclk2ioe 3.4 3.7 4.5 ns t dclk2le 1.1 1.2 1.7 ns t samelab 0.3 0.3 0.4 ns t samerow 2.0 2.4 3.3 ns t samecolumn 1.7 2.1 2.9 ns t diffrow 3.7 4.5 6.2 ns t tworows 5.7 6.9 9.5 ns t leperiph 4.8 4.8 5.2 ns t labcarry 0.0 0.0 0.0 ns t labcasc 0.4 0.4 0.5 ns table 72. epf10k100b external timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t drr 11.0 12.0 14.5 ns t insu 3.5 3.8 4.6 ns t inh 0.0 0.0 0.0 ns t outco 2.0 4.8 2.0 5.7 2.0 7.2 ns
altera corporation 95 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet notes to tables: (1) all timing parameters are described in tables 24 through 31 in this data sheet. (2) th ese parameter s are s pecified by characterization. tables 74 through 77 show epf10k50s and epf10k200s device external timing parameters. table 73. epf10k100b external bidirectional timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t insubidir 4.1 4.5 5.5 ns t inhbidir 0.0 0.0 0.0 ns t outcobidir 2.0 4.8 2.0 5.7 2.0 7.2 ns t xzbidir 8.4 9.0 11.0 ns t zxbidir 8.4 9.0 11.0 ns table 74. epf10k 50s e xternal timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t drr 8.5 10.0 13.5 ns t insu (3) 3.0 3.6 4.8 ns t inh (3) 0.0 0.0 0.0 ns t outco (3) 2.0 3.5 2.0 4.5 2.0 7.1 ns t insu (4) 2.0 2.6 ns t inh (4) 0.0 0.0 ns t outco (4) 0.5 2.5 0.5 3.5 ns t pcisu 3.0 4.2 6.4 ns t pcih 0.0 0.0 0.0 ns t pcico 2.0 6.0 2.0 7.7 2.0 10.5 ns
96 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation table 75. epf10k 50s e xternal bidirectional timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t insubdir 1.5 2.2 3.6 ns t inhbidir 0.0 0.0 0.0 ns t outcobidir (3) 2.0 3.5 2.0 4.5 2.0 7.1 ns t xzbidir (3) 2.0 5.8 2.0 6.3 2.0 8.0 ns t zxbidir (3) 2.0 4.7 2.0 5.3 2.0 7.2 ns t outcobidir (4) 0.5 2.5 0.5 3.5 ns t xzbidir (4) 0.5 4.8 0.5 5.3 ns t zxbidir (4) 0.5 3.7 0.5 4.3 ns table 76. epf10k200s external timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t drr 10.0 12.0 16.0 ns t insu (3) 3.1 3.7 4.7 ns t inh (3) 0.0 0.0 0.0 ns t outco (3) 2.0 3.7 2.0 4.4 2.0 6.3 ns t insu (4) 2.1 2.7 ns t inh (4) 0.0 0.0 ns t outco (4) 0.5 2.7 0.5 3.4 ns t pcisu 3.0 4.2 ns t pcih 0.0 0.0 ns t pcico 2.0 6.0 2.0 8.9 ns
altera corporation 97 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet note s to tables: (1) all timing parameters are described in tables 30 and 31 in this data sheet. (2) these parameters are specified by characterization. (3) this parameter is measured without the use of the clocklock or clockboost circuits. (4) this parameter is measured with the use of the clocklock or clockboost circuits. power consumption the supply power (p) for flex 10ke devices can be calculated with the following equation: p = p int + p io = (i c cstandby + i cc active ) v cc + p io the i cc active v alue depends on the switching frequency and the application logic. this value is calculated based on the amount of current that each le typically consumes. the p io value, which depends on the device output load characteristics and switching frequency, can be calculated using the guidelines given in application note 74 (evaluating power for altera devices) . 1 compared to the rest of the device, the embedded array consumes a negligible amount of power. therefore, the embedded array can be ignored when calculating supply current. table 77. epf10k 200s e xternal bidirectional timing parameters notes (1) , (2) symbol speed grade unit -1 -2 -3 min max min max min max t insubdir 2.5 3.3 4.4 ns t inhbidir 0.0 0.0 0.0 ns t outcobidir (3) 2.0 3.7 2.0 4.4 2.0 ns t xzbidir (3) 2.0 5.2 2.0 6.1 2.0 ns t zxbidir (3) 2.0 4.7 2.0 5.6 2.0 ns t outcobidir (4) 0.5 2.7 0.5 3.4 ns t xzbidir (4) 0.5 4.2 0.5 5.1 ns t zxbidir (4) 0.5 3.7 0.5 4.6 ns
98 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation the i cc active v alue can be calculated with the following equation: i cc active = k f max n tog lc where: f max = maximum operating frequency in mhz n = total number of les used in the device tog lc = average percent of les toggling at each clock (typically 12.5 % ) k = constant table 78 provides the constant (k) values for flex 10ke devices. this calculation provides an i cc estimate based on typical conditions with no output load. the actual i cc should be verified during operation because this measurement is sensitive to the actual pattern in the device and the environmental operating conditions. to better reflect actual designs, the power model (and the constant k in the power calculation equations) for continuous interconnect flex devices assumes that les drive fasttrack interconnect channels. in contrast, the power model of segmented fpgas assumes that all les drive only one short interconnect segment. this assumption may lead to inaccurate results when compared to measured power consumption for actual designs in segmented fpgas. figure 29 shows the relationship between the current and operating frequency of flex 10ke devices. for information on other flex 10ke devices, contact altera applications at (800) 800-epld. table 78. flex 10ke k constant values device k value epf10k30e 4.5 epf10k50e 4.8 epf10k50s 4.5 epf10k100b 5.0 epf10k100e 4.5 EPF10K130E 4.6 epf10k200e 4.8 epf10k200s 4.6 m a mhz le - - - - - - - - - - - - - - - - - - - - - - - - - - -
altera corporation 99 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet figure 29. flex 10ke i ccactive vs. operating frequency (part 1 of 2) 0 f r e q u e n c y ( m h z ) i c c s u p p l y c u r r e n t ( m a ) 1 0 0 8 0 6 0 4 0 2 0 5 0 1 0 0 e p f 1 0 k 3 0 e 0 f r e q u e n c y ( m h z ) i c c s u p p l y c u r r e n t ( m a ) 2 0 0 1 5 0 1 0 0 5 0 5 0 1 0 0 e p f 1 0 k 5 0 s 0 f r e q u e n c y ( m h z ) 3 0 0 2 0 0 1 0 0 5 0 1 0 0 e p f 1 0 k 1 0 0 e i c c s u p p l y c u r r e n t ( m a ) 0 f r e q u e n c y ( m h z ) 4 0 0 3 0 0 2 0 0 1 0 0 5 0 1 0 0 e p f 1 0 k 1 3 0 e i c c s u p p l y c u r r e n t ( m a ) 0 f r e q u e n c y ( m h z ) i c c s u p p l y c u r r e n t ( m a ) 2 0 0 1 5 0 1 0 0 5 0 5 0 1 0 0 e p f 1 0 k 5 0 e 0 f r e q u e n c y ( m h z ) 5 0 1 0 0 e p f 1 0 k 1 0 0 b 2 0 0 1 0 0 3 0 0 i c c s u p p l y c u r r e n t ( m a )
100 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation figure 29 . flex 10ke i ccactive vs. operating frequency (part 2 of 2) con guration & operation the flex 10ke architecture supports several configuration schemes. this section summarizes the device operating modes and available device configuration schemes. operatin g modes the flex 10ke architecture uses sram configuration elements that require configuration data to be loaded every time the circuit powers up. the process of physically loading the sram data into the device is called configuration . before configuration, as v cc rises, the device initiates a power-on reset (por). this por event clears the device and prepares it for configuration. the flex 10ke por time does not exceed 50 ?; however, when configuring with a co nfiguration device, the co nfiguration device i mposes a 100- ms delay that allows system power to stabilize before configuration. during initialization, which occurs immediately after configuration, the device resets registers, enables i/o pins, and begins to operate as a logic device. the i/o pins are tri-stated during power-up, and before and during configuration. together, the configuration and initialization processes are called command mode ; normal device operation is called user mode . sram configuration elements allow flex 10ke devices to be reconfigured in-circuit by loading new configuration data into the device. real-time reconfiguration is performed by forcing the device into command mode with a device pin, loading different configuration data, reinitializing the device, and resuming user-mode operation. the entire reconfiguration process requires less than 276 ms and can be used to reconfigure an entire system dynamically. in-field upgrades can be performed by distributing new configuration files. 0 f r e q u e n c y ( m h z ) 6 0 0 4 0 0 2 0 0 5 0 1 0 0 e p f 1 0 k 2 0 0 e i c c s u p p l y c u r r e n t ( m a ) 0 f r e q u e n c y ( m h z ) 6 0 0 4 0 0 2 0 0 5 0 1 0 0 e p f 1 0 k 2 0 0 s i c c s u p p l y c u r r e n t ( m a )
altera corporation 101 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet before and during configuration, all i/o pins (except dedicated inputs, clock, or configuration pins) are pulled high by a weak pull-up resistor. programming files despite being function- and pin-compatible, flex 10ke devices are not programming- or configuration f ile-compatible with flex 10k or flex 10ka devices. a design therefore must be recompiled before it is transferred from a flex 10k or flex 10ka device to an equivalent flex 10ke device. this recompilation should be performed both to create a new programming or configuration file and to check design timing in fl ex 10ke device s, which has different timing characteristics tha n f lex 1 0k or flex 10ka devices. flex 10ke devices are generally pin-compatible with e quivalen t f lex 1 0ka device s . in some cases, flex 10ke devices have fewer i/o pins than the equivalent f lex 10ka devices. table 79 shows which flex 1 0ke devices have fewer i/o pins than equivalent flex 10ka devices . however, power, ground, jtag, and configuration pins are the same on flex 10ka and flex 10ke devices, enabling migration from a flex 10ka design to a flex 10ke design . additionally, q uartus and max+plus ii software offer features to help plan for future device migration by preventing the use of conflicting i/o pins. table 79. i/o count s for f lex 10ka & flex 10ke devices flex 10ka flex 10ke device i/o count device i/o count epf10k30af256 191 epf10k30ef256 176 epf10k30af484 24 6 epf10k30ef484 2 20 epf10k50v b356 274 epf10k50e b356 220 epf10k 50vb356 274 epf10k 50sb356 220 epf10k50vf484 291 epf10k50ef484 254 epf10k50vf484 291 epf10k50sf484 254 epf10k100af484 369 epf10k100ef484 338
102 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation con guration schemes the configuration data for a flex 10ke device can be loaded with one of five configuration schemes (see table 80 ), chosen on the basis of the target application. an epc2, epc1, or epc1441 co nfiguration device, intelligent controller, or the jtag port can be used to control the configuration of a flex 10ke device, allowing automatic configuration on system power- up. multiple flex 10ke devices can be configured in any of the five configuration schemes by connecting the configuration enable ( nce ) and configuration enable output ( nceo ) pins on each device. additional flex 10k, flex 10ka, flex 10ke, and flex 6000 devices can be configured in the same serial chain. table 80. data sources for flex 10ke configuration configuration scheme data source configuration device epc1, epc2, or epc1441 co nfiguration device passive serial (ps) bitblaster, byteblaster, or byteblastermv download cables, or serial data source passive parallel asynchronous (ppa) parallel data source passive parallel synchronous (pps) parallel data source jtag bitblaster or byteblastermv download cables, or microprocessor with a jam file or jbc file
altera corporation 103 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet dev ic e pin- outs tables 81 and 82 shows the dedicated pin-outs for flex 10ke devices in 144-pin tqfp, 208-pin pqfp, 240-pin pqfp, 356-pin bga, 599-pin pga, and 600 - pin bga packages. table 81. flex 10ke device pin-outs (part 1 of 2) note (1) pin name 144-pin tqfp epf10k30e epf10k50e epf10k50s 208-pin pqfp epf10k30e epf10k50e epf10k50s epf10k100e epf10k100b 240-pin pqfp (2) , (3) epf10k50e epf10k50s epf10k100e epf10k100b 240-pin pqfp (2) EPF10K130E 240-pin rqfp (3) epf10k200s msel0 (4) 77 108 124 124 124 msel1 (4) 76 107 123 123 123 nstatus (4) 35 52 60 60 60 nconfig (4) 74 105 121 121 121 dclk (4) 107 155 179 179 179 conf_done (4) 2 2 2 2 2 init_done (5) 14 19 26 26 26 nce (4) 106 154 178 178 178 nceo (4) 3 3 3 3 3 nws (6) 142 206 238 238 238 nrs (6) 141 204 236 236 236 ncs (6) 144 208 240 240 240 cs (6) 143 207 239 239 239 rdynb u sy (6) 11 16 23 23 23 clkusr (6) 7 10 11 11 11 data7 (6) 116 166 190 190 190 data6 (6) 114 164 188 188 188 data5 (6) 113 162 186 186 186 data4 (6) 112 161 185 185 185 data3 (6) 111 159 183 183 183 data2 (6) 110 158 182 182 182 data1 (6) 109 157 181 181 181 data0 (4) , (7) 108 156 180 180 180 tdi (4) 105 153 177 177 177 tdo (4) 4 4 4 4 4 tck (4) 1 1 1 1 1 tms (4) 34 50 58 58 58 trst (4) (8) 51 59 59 59
104 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation dedicated inputs 54, 56, 124, 126 78, 80, 182, 184 90, 92, 210, 212 90, 92, 210, 212 90, 92, 210, 212 dedicated clock pins 55, 125 79, 183 91, 211 91, 211 91, 211 gclk1 (9) 55 79 91 91 91 lock (10) 42 62 73 73 73 dev_clrn (5) 122 180 209 209 209 dev_oe (5) 128 186 213 213 213 vccint (2.5 v) 6, 25, 52, 7 5, 93, 123 6, 23, 35, 43, 76, 1 06, 109, 117, 137, 145, 181 5, 27, 47, 9 6, 122, 130, 150, 170 5, 20, 27, 47, 76, 9 6, 122, 130, 150, 159, 170 5, 20, 27, 40, 47, 76, 96, 122, 130, 139, 150, 159, 170, 187, 225 vccio (2.5 or 3.3 v) 5, 24, 45, 61, 71, 94, 115, 134 5, 22, 34, 42, 66, 84, 98, 110, 118, 138, 146, 165, 178, 194 16, 37, 57, 77, 112, 140, 160, 189, 205, 224 16, 37, 57, 77, 112, 140, 160, 189, 205, 224 16, 37, 57, 77, 112, 140, 160, 189, 205, 224 vcc_cklk (11) 53 77 (12) 89 (12) 89 89 gndint 15, 16, 40, 50, 5 8, 66, 84, 85, 103, 104, 127, 129, 139 20, 21, 32, 33, 48, 49, 59, 72, 8 2, 91, 123, 124, 129, 130, 151, 152, 171, 185, 188, 201 10, 22, 32, 42, 52, 69, 85, 1 04, 125, 135, 145, 155, 165, 176, 197, 216, 232 10, 22, 32, 42, 52, 69, 85, 1 04, 125, 135, 145, 155, 165, 176, 197, 216, 232 10, 22, 32, 42, 52, 69, 85, 104, 125, 135, 145, 155, 165, 176, 197, 216, 232 gndio gnd_cklk (11) 57 81 (13) 93 (13) 93 93 total user i/o pins (14) 102 147 189 186 182 table 81. flex 10ke device pin-outs (part 2 of 2) note (1) pin name 144-pin tqfp epf10k30e epf10k50e epf10k50s 208-pin pqfp epf10k30e epf10k50e epf10k50s epf10k100e epf10k100b 240-pin pqfp (2) , (3) epf10k50e epf10k50s epf10k100e epf10k100b 240-pin pqfp (2) EPF10K130E 240-pin rqfp (3) epf10k200s
altera corporation 105 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 82. flex 10ke device pin-outs (part 1 of 4) note (1) pin name 356-pin bga epf10k50e epf10k50s 356-pin bga epf10k100e EPF10K130E epf10k200s 599-pin pga epf10k200e epf10k200s 600-pin bga EPF10K130E 600-pin bga epf10k200e epf10k200s msel0 (4) d4 d4 f6 f5 f5 msel1 (4) d3 d3 c3 c1 c1 nstatus (4) d24 d24 e43 d32 d32 nconfig (4) d2 d2 b4 d4 d4 dclk (4) ac5 ac5 be5 ap1 ap1 conf_done (4) ac24 ac24 bc43 am32 am32 init_done (5) t24 t24 am40 ae32 ae32 nce (4) ac2 ac2 bb6 an2 an2 nceo (4) ac22 ac22 bf44 ap35 ap35 nws (6) ae24 ae24 bb40 ar29 ar29 nrs (6) ae23 ae23 ba37 am28 am28 ncs (6) ad24 ad24 ay38 al29 al29 cs (6) ad23 ad23 ba39 an29 an29 rdynbusy (6) u22 u22 aw47 ag35 ag35 clkusr (6) aa24 aa24 ay42 am34 am34 data7 (6) af4 af4 bd14 am13 am13 data6 (6) ad8 ad8 ba17 ar12 ar12 data5 (6) ae5 ae5 bb16 an12 an12 data4 (6) ad6 ad6 bf12 ap11 ap11 data3 (6) af2 af2 bg11 am11 am11 data2 (6) ad5 ad5 bg9 ar10 ar10 data1 (6) ad4 ad4 bf10 an10 an10 data0 (4) , (7) ad3 ad3 bc5 am4 am4 tdi (4) ac3 ac3 bf4 an1 an1 tdo (4) ac23 ac23 bb42 an34 an34 tck (4) ad25 ad25 be43 al31 al31 tms (4) d22 d22 f42 c35 c35 trst (4) d23 d23 b46 c34 c34 dedicated inputs a13, b14, af14, ae13 a13, b14, af14, ae13 b24, c25, bg25, bg23 c18, d18, am18, an18 c18, d18, am18, an18 dedicated clock pins a14, af13 a14, af13 bf24, a25 al18, e18 al18, e18 gclk1 (9) a14 a14 e18 e18 lock (10) c18 c18 a23 a23
106 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation dev_clrn (5) ad13 ad13 be23 ar17 ar17 dev_oe (5) ae14 ae14 bc25 ar19 ar19 vccint (2.5 v) a1, a26, c26, d5, f1, h22, j1, m26, n1, t26, u5, aa1, ad26, af1, af26 a1, a26, c26, d5, f1, h22, j1, m26, n1, t26, u5, aa1, ad26, af1, af26 a3, a45, c1, c11, c19, c29, c37, c47, e5, g25, l3, l45, w3, w45, aj3, aj45, au3, au45, be1, be11, be19, be29, be37, be47, bg3, bg45 a11, a19, b1, d24, e2, f31, f35, h1, k32, m2, n34, p5, t35, u3, v32, y2, aa33, ab5, ad35, ae4, af32, ag5, ak31, ak35, al3, ap24, ar11, ar18 a11, a19, b1, d24, e2, f31, f35, h1, k32, m2, n34, p5, t35, u3, v32, y2, aa33, ab5, ad35, ae4, af32, ag5, ak31, ak35, al3, ap24, ar11, ar18 vccio (2.5 or 3.3 v) a7, a23, b4, c15, d25, f4, h24, k5, m23, p2, t25, v2, w22, ab1, ac25, ad18, af3, af7, af16 a7, a23, b4, c15, d25, f4, h24, k5, m23, p2, t25, v2, w22, ab1, ac25, ad18, af3, af7, af16 d24, e9, e15, e21, e27, e33, e39, g7, g41, j5, j43, r5, r43, aa5, aa43, ad4, ad44, ag5, ag43, an5, an43, aw5, aw43, ba7, ba41, bc9, bc15, bc21, bc27, bc33, bc39, bd24 c8, e12, c15, a20, c23, a27, am26, ar23, am19, an15, al12, an8, c2, c3, c4, d5, e5, c33, c32, d31, e31, al5, am5, an4, an3, am31, an32, an33, ap34 c8, e12, c15, a20, c23, a27, am26, ar23, am19, an15, al12, an8, c2, c3, c4, d5, e5, c33, c32, d31, e31, al5, am5, an4, an3, am31, an32, an33, ap34 vcc_cklk (11) c14 c14 b18 b18 table 82. flex 10ke device pin-outs (part 2 of 4) note (1) pin name 356-pin bga epf10k50e epf10k50s 356-pin bga epf10k100e EPF10K130E epf10k200s 599-pin pga epf10k200e epf10k200s 600-pin bga EPF10K130E 600-pin bga epf10k200e epf10k200s
altera corporation 107 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet gndint a2, a10, a20, b1, b22, b25, b26, c2, c9, c13, c25, h23, j26, k1, m1, n26, r1, r26, t1, u26, w1, ad2, ad14, ad20, ae1, ae2, ae7, ae25, ae26, af11, af19, af25 a2, a10, a20, b1, b22, b25, b26, c2, c9, c13, c25, h23, j26, k1, m1, n26, r1, r26, t1, u26, w1, ad2, ad14, ad20, ae1, ae2, ae7, ae25, ae26, af11, af19, af25 a47, b2, c13, c21, c27, c35, c45, d4, g23, n3, n45, aa3, aa45, ag3, ag45, ar3, ar45, bd44, be3, be13, be21, be27, be35, be45, bg1, bg47 a1, a2, a3, a4, a5, a31, a32, a33, a34, a35, b2, b3, b4, b5, b6, b31, b32, b33, b34, b35, c5, c6, d6, e6, c30, c31, d30, e30, al6, al30, am6, am30, an5, an6, an30, an31, an35, ap2, ap3, ap4, ap5, ap6, ap30, ap31, ap32, ap33, ar1, ar2, ar3, ar4, ar5, ar30, ar31, ar32, ar33, ar34, ar35 a1, a2, a3, a4, a5, a31, a32, a33, a34, a35, b2, b3, b4, b5, b6, b31, b32, b33, b34, b35, c5, c6, d6, e6, c30, c31, d30, e30, al6, al30, am6, am30, an5, an6, an30, an31, an35, ap2, ap3, ap4, ap5, ap6, ap30, ap31, ap32, ap33, ar1, ar2, ar3, ar4, ar5, ar30, ar31, ar32, ar33, ar34, ar35 gndio e7, e13, e19, e29, e35, e41, f24, g5, g43, h40, n5, n43, w5, w43, ad6, ad42, aj5, aj43, ar5, ar43, ay8, ay40, ba5, ba43, bb24, bc7, bc13, bc19, bc29, bc35, bc41 gnd_cklk (11) b13 b13 a18 a18 table 82. flex 10ke device pin-outs (part 3 of 4) note (1) pin name 356-pin bga epf10k50e epf10k50s 356-pin bga epf10k100e EPF10K130E epf10k200s 599-pin pga epf10k200e epf10k200s 600-pin bga EPF10K130E 600-pin bga epf10k200e epf10k200s
108 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation no connect (n.c.) d1, e2, e22, e25, f5, f23, f26, g3, g22, g25, h4, h5, j2, j4, j23, j24, k2, k3, k25, k26, l2, l23, l26, m2, m5, m22, m25, n4, n25, p1, p5, p22, p23, r5, t22, u2, u3, u23, u24, v4, w3, w4, w24, w26, y2, y5, aa3, aa22, aa25, ab3, ab5, ab22, ab24, ab26 d3, d35, e1, f34, g2, h5, j3, j4, j32, k1, l4, l31, m3, n1, n33, n35, p4, p33, r2, r32, t4, u5, u34, v3, v34, w1, w32, w35, y31, aa2, aa34, ab1, ab31, ab34, ab35, ac31, ac34, ae33, ae35, af1, ag3, ah2, aj32, ak2, ak32, al33 total user i/o pins (14) 220 274 470 424 470 table 82. flex 10ke device pin-outs (part 4 of 4) note (1) pin name 356-pin bga epf10k50e epf10k50s 356-pin bga epf10k100e EPF10K130E epf10k200s 599-pin pga epf10k200e epf10k200s 600-pin bga EPF10K130E 600-pin bga epf10k200e epf10k200s
altera corporation 109 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet notes to tables: (1) all pins that are not listed are user i/o pins. (2) epf10k50e, epf10k100e, and epf10k100b devices are pin-compatible with the epf10k 1 30e devices in the same package if pins 20, 76, and 159 are connected to vccint . the quartus and max+plus ii software performs this function automatically when future migration is set. (3) epf10k50e, epf10k100e, and epf10k100b devices are pin-compatible with the epf10k 200 e devices in the same package if pins 20, 40, 76, 139, 159, 187, and 225 are connected to vccint . the quartus and max+plus ii software performs this function automatically when future migration is set. (4) this pin is a dedicated pin; it is not available as a user i/o pin. (5) this pin can be used as a user i/o pin if it is not used for its device-wide or configuration function. (6) this pin can be used as a user i/o pin after configuration. (7) this pin is tri-stated in user mode. (8) the optional jtag pin trst is not used in the 144-pin tqfp package. (9) this pin drives the clocklock and clockboost circuitry. (10) this pin shows the status of the clocklock and clockboost circuitry. when the clocklock and clockboost circuitry is locked to the incoming clock and generates an internal clock, lock is driven high. lock remains high if a periodic clock stops clocking. the lock function is optional; if the lock output is not used, this pin is a user i/o pin. (11) this pin is the power or ground for the clocklock and clockboost circuitry. to ensure noise resistance, the power and ground supply to the clocklock and clockboost circuitry should be isolated from the power and ground to the rest of the device. if the clocklock or clockboost circuitry is not used, this power or ground pin should be connected to vccint or gndint , respectively. (12) when using the epf10k100b device, connect this pin t o vccint . (13) when using the epf10k100b device, connect this pin t o gndint . (14) the user i/o pin count includes dedicated input pins, dedicated clock pins, and all i/o pins. tables 83 through 85 show the dedicated pin-outs for flex 10ke devices in 256-pin fineline bga, 484-pin fineline bga, and 672-pin fineline bga packages. table 83. flex 10ke fineline bga device pin-outs (part 1 of 4) notes (1) , (2) pin name 256-pin fineline bga epf10k30e 256-pin fineline bga epf10k50e epf10k50s epf10k100e epf10k100b 484-pin fineline bga epf10k30e msel0 (3) p1 p1 u4 msel1 (3) r1 r1 v4 nstatus (3) t16 t16 w19 nconfig (3) n4 n4 t7 dclk (3) b2 b2 e5 conf_done (3) c15 c15 f18 init_done (4) g16 g16 k19 nce (3) b1 b1 e4 nceo (3) b16 b16 e19 nws (5) b14 b14 e17 nrs (5) c14 c14 f17
110 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation ncs (5) a16 a16 d19 cs (5) a15 a15 d18 rdynbsy (5) g14 g14 k17 clkusr (5) d15 d15 g18 data7 (5) b5 b5 e8 data6 (5) d4 d4 g7 data5 (5) a4 a4 d7 data4 (5) b4 b4 e7 data3 (5) c3 c3 f6 data2 (5) a2 a2 d5 data1 (5) b3 b3 e6 data0 (3) , (6) a1 a1 d4 tdi (3) c2 c2 f5 tdo (3) c16 c16 f19 tck (3) b15 b15 e18 tms (3) p15 p15 u18 trst (3) r16 r16 v19 dedicated inputs b9, e8, m9, r8 b9, e8, m9, r8 e12, h11, r12, v11 dedicated clock pins a9, l8 a9, l8 d12, p11 gclk1 (7) l8 l8 p11 lock (8) p12 p12 u15 dev_clrn (4) d8 d8 g11 dev_oe (4) c9 c9 f12 vccint (2.5 v) e11, f5, f7, f9, f12, h6, h7, h10, j7, j10, j11, k9, l5, l7, l12, m11, r2 e11, f5, f7, f9, f12, h6, h7, h10, j7, j10, j11, k9, l5, l7, l12, m11, r2 c11, c15, h14, j8, j10, j12, j15, l9, l10, l13, m10, m13, m14, n12, p8, p10, p15, r14, v5, w21, y8, aa12 vccio (2.5 or 3.3 v) d12, e6, f8, f10, g6, g8, g11, h11, j6, k6, k8, k11, l10, m6, n12 d12, e6, f8, f10, g6, g8, g11, h11, j6, k6, k8, k11, l10, m6, n12 a6, a13, b5, e1, g1, g15, h9, h20, j11, j13, k9, k11, k14, k20, l14, m9, n3, n9, n11, n14, n20, p13, r1, r9, t3, t15, t22, v22, ab13 table 83. flex 10ke fineline bga device pin-outs (part 2 of 4) notes (1) , (2) pin name 256-pin fineline bga epf10k30e 256-pin fineline bga epf10k50e epf10k50s epf10k100e epf10k100b 484-pin fineline bga epf10k30e
altera corporation 111 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet vcc_cklk (9) l9 l9 (10) p12 gnd e5, e12, f6, f11, g7, g9, g10, h8, h9, j8, j9, k7, k10, l6, l11, m5, m12 e5, e12, f6, f11, g7, g9, g10, h8, h9, j8, j9, k7, k10, l6, l11, m5, m12 a1, a8, a22, b1, b2, b17, b21, b22, c2, c21, e21, g3, g21, h2, h8, h15, j9, j14, j20, k3, k10, k12, k13, l11, l12, m11, m12, m20, n10, n13, p9, p14, r8, r15, r22, t1, v3, w20, y1, y2, y3, y21, y22, aa1, aa6, aa22, ab11, ab16 gnd_cklk (9) t8 t8 (11) w11 table 83. flex 10ke fineline bga device pin-outs (part 3 of 4) notes (1) , (2) pin name 256-pin fineline bga epf10k30e 256-pin fineline bga epf10k50e epf10k50s epf10k100e epf10k100b 484-pin fineline bga epf10k30e
112 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation no connect (n.c.) d1, e3, e16, g3, h1, h16, j1, k3, k14, k16, l2, l4, m14, m16, n15 a2, a3, a4, a5, a7, a9, a11, a12, a14, a15, a20, a21, b3, b4, b9, b10, b12, b16, b19, b20, c1, c6, c9, c10, c12, c13, c14, c16, c17, c22, d1, d2, d3, d20, d21, d22, e2, e3, e20, e22, f1, f2, f3, f20, f21, f22, g2, g4, g20, g22, h1, h3, h6, h19, h21, h22, j1, j2, j3, j21, j22, k1, k2, k6, k21, k22, l1, l2, l3, l4, l19, l20, l21, l22, m1, m2, m3, m4, m21, m22, n1, n2, n21, n22, n6, n17, n19, p1, p2, p3, p5, p7, p20, p21, p22, r2, r3, r17, r19, r20, r21, t2, t18, t20, t21, u1, u2, u3, u20, u21, u22, v1, v2, v20, v21, w1, w2, w22, y4, y9, y12, y13, y16, y19, y20, aa2, aa3, aa4, aa9, aa11, aa13, aa15, aa21, ab1, ab2, ab3, ab4, ab5, ab7, ab8, ab9, ab12, ab15, ab17, ab18, ab19, ab20, ab21, ab22 total user i/o pins (12) 176 191 220 table 83. flex 10ke fineline bga device pin-outs (part 4 of 4) notes (1) , (2) pin name 256-pin fineline bga epf10k30e 256-pin fineline bga epf10k50e epf10k50s epf10k100e epf10k100b 484-pin fineline bga epf10k30e
altera corporation 113 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 84. flex 10ke fineline bga device pin-outs (part 1 of 2) notes (1) , (2) pin name 484-pin fineline bga epf10k50e epf10k50s 484-pin fineline bga epf10k100e msel0 (3) u4 u4 msel1 (3) v4 v4 nstatus (3) w19 w19 nconfig (3) t7 t7 dclk (3) e5 e5 conf_done (3) f18 f18 init_done (4) k19 k19 nce (3) e4 e4 nceo (3) e19 e19 nws (5) e17 e17 nrs (5) f17 f17 ncs (5) d19 d19 cs (5) d18 d18 rdynbsy (5) k17 k17 clkusr (5) g18 g18 data7 (5) e8 e8 data6 (5) g7 g7 data5 (5) d7 d7 data4 (5) e7 e7 data3 (5) f6 f6 data2 (5) d5 d5 data1 (5) e6 e6 data0 (3) , (6) d4 d4 tdi (3) f5 f5 tdo (3) f19 f19 tck (3) e18 e18 tms (3) u18 u18 trst (3) v19 v19 dedicated inputs e12, h11, r12, v11 e12, h11, r12, v11 dedicated clock pins d12, p11 d12, p11 gclk1 (7) p11 p11 lock (8) u15 u15 dev_clrn (4) g11 g11 dev_oe (4) f12 f12
114 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation vccint (2.5 v) c11, c15, h14, j8, j10, j12, j15, l9, l10, l13, m10, m13, m14, n12, p8, p10, p15, r14, v5, w21, y8, aa12 c11, c15, h14, j8, j10, j12, j15, l9, l10, l13, m10, m13, m14, n12, p8, p10, p15, r14, v5, w21, y8, aa12 vccio (2.5 or 3.3 v) a6, a13, b5, e1, g1, g15, h9, h20, j11, j13, k9, k11, k14, k20, l14, m9, n3, n9, n11, n14, n20, p13, r1, r9, t3, t15, t22, v22, ab13 a6, a13, b5, e1, g1, g15, h9, h20, j11, j13, k9, k11, k14, k20, l14, m9, n3, n9, n11, n14, n20, p13, r1, r9, t3, t15, t22, v22, ab13 vcc_cklk (9) p12 p12 gnd a1, a8, a22, b1, b2, b17, b21, b22, c2, c21, e21, g3, g21, h2, h8, h15, j9, j14, j20, k3, k10, k12, k13, l11, l12, m11, m12, m20, n10, n13, p9, p14, r8, r15, r22, t1, v3, w20, y1, y2, y3, y21, y22, aa1, aa6, aa22, ab11, ab16 a1, a8, a22, b1, b2, b17, b21, b22, c2, c21, e21, g3, g21, h2, h8, h15, j9, j14, j20, k3, k10, k12, k13, l11, l12, m11, m12, m20, n10, n13, p9, p14, r8, r15, r22, t1, v3, w20, y1, y2, y3, y21, y22, aa1, aa6, aa22, ab11, ab16 gnd_cklk (9) w11 w11 no connect (n.c.) a2, a3, a4, a5, a7, a9, a11, a12, a14, a15, a20, a21, b3, b4, b9, b10, b12, b16, b19, b20, c1, c6, c9, c10, c12, c13, c14, c16, c17, c22, d1, d2, d3, d20, d21, e2, e3, e20, e22, f1, f2, f20, f21, g2, g20, g22, j1, j2, j3, j21, k2, k22, l1, l2, l20, l22, m2, m3, m22, n1, n2, n21, n22, p3, p20, p21, p22, r2, r3, r21, t2, t20, t21, u1, u2, u3, u20, u21, u22, v2, v20, w1, w2, w22, y4, y9, y12, y13, y16, y19, y20, aa2, aa3, aa4, aa9, aa11, aa13, aa15, aa21, ab1, ab2, ab3, ab4, ab5, ab7, ab8, ab9, ab12, ab15, ab17, ab18, ab19, ab20, ab21, ab22 a2, a3, a4, a5, b3, b4, b10, c17, f2, j2, k2, l2, n1, p20, p22, r3, t20, t21, u1, w22, y16, aa15, ab3, ab4, ab5, ab7, ab15, ab17, ab18, ab19, ab20 total user i/o pins (12) 254 338 table 84. flex 10ke fineline bga device pin-outs (part 2 of 2) notes (1) , (2) pin name 484-pin fineline bga epf10k50e epf10k50s 484-pin fineline bga epf10k100e
altera corporation 115 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 85. flex 10ke fineline bga device pin-outs (part 1 of 3) notes (1) , (2) pin name 484-pin fineline bga EPF10K130E epf10k200s 672-pin fineline bga EPF10K130E 672-pin fineline bga epf10k200e epf10k200s msel0 (3) u4 w6 w6 msel1 (3) v4 y6 y6 nstatus (3) w19 aa21 aa21 nconfig (3) t7 v9 v9 dclk (3) e5 g7 g7 conf_done (3) f18 h20 h20 init_done (4) k19 m21 m21 nce (3) e4 g6 g6 nceo (3) e19 g21 g21 nws (5) e17 g19 g19 nrs (5) f17 h19 h19 ncs (5) d19 f21 f21 cs (5) d18 f20 f20 rdynbsy (5) k17 m19 m19 clkusr (5) g18 j20 j20 data7 (5) e8 g10 g10 data6 (5) g7 j9 j9 data5 (5) d7 f9 f9 data4 (5) e7 g9 g9 data3 (5) f6 h8 h8 data2 (5) d5 f7 f7 data1 (5) e6 g8 g8 data0 (3) , (6) d4 f6 f6 tdi (3) f5 h7 h7 tdo (3) f19 h21 h21 tck (3) e18 g20 g20 tms (3) u18 w20 w20 trst (3) v19 y21 y21 dedicated inputs e12, h11, r12, v11 y13, u14, g14, k13 y13, u14, g14, k13 dedicated clock pins d12, p11 t13, f14 t13, f14 gclk1 (7) p11 t13 t13 lock (8) u15 w17 w17 dev_clrn (4) g11 j13 j13 dev_oe (4) f12 h14 h14
116 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation vccint (2.5 v) c11, c15, h14, j8, j10, j12, j15, l9, l10, l13, m10, m13, m14, n12, p8, p10, p15, r14, v5, w21, y8, aa12 e13, e17, h2, h25, k16, l10, l12, l14, l17, m2, m25, n11, n12, n15, p12, p15, p16, r14, t2, t10,t12, t17, t25, u16, y7, aa23, ab10, ac14 e13, e17, h2, h25, k16, l10, l12, l14, l17, m2, m25, n11, n12, n15, p12, p15, p16, r14, t2, t10,t12, t17, t25, u16, y7, aa23, ab10, ac14 vccio (2.5 or 3.3 v) a6, a13, b5, e1, g1, g15, h9, h20, j11, j13, k9, k11, k14, k20, l14, m9, n3, n9, n11, n14, n20, p13, r1, r9, t3, t15, t22, v22, ab13 c8, c15, d7, g3, j3, j17, k11, k22, l13, l15, m11, m13, m16, m22, n16, p11, r5, r11, r13, r16, r22, t15, u3, u11, v5, v17, v24, y2, y24, aa26, ad15 c8, c15, d7, g3, j3, j17, k11, k22, l13, l15, m11, m13, m16, m22, n16, p11, r5, r11, r13, r16, r22, t15, u3, u11, v5, v17, v24, y2, y24, aa26, ad15 vcc_cklk (9) p12 t14 t14 gnd a1, a8, a22, b1, b2, b17, b21, b22, c2, c21, e21, g3, g21, h2, h8, h15, j9, j14, j20, k3, k10, k12, k13, l11, l12, m11, m12, m20, n10, n13, p9, p14, r8, r15, r22, t1, v3, w20, y1, y2, y3, y21, y22, aa1, aa6, aa22, ab11, ab16 a2, a25, b2, b25, c3, c10, c24, d3, d4, d19, d23, d24, e4, e23, g23, j5, j23, k4, k10, k17, l11, l16, l22, m5, m12, m14, m15, n13, n14, p13, p14, p22, r12, r15, t11, t16, u10, u17, u24, v3, y5, aa22, ab3, ab4, ab5, ab23, ab24, ac3, ac8, ac24, ad13, ad18, ae2, ae25, af2, af25 a2, a25, b2, b25, c3, c10, c24, d3, d4, d19, d23, d24, e4, e23, g23, j5, j23, k4, k10, k17, l11, l16, l22, m5, m12, m14, m15, n13, n14, p13, p14, p22, r12, r15, t11, t16, u10, u17, u24, v3, y5, aa22, ab3, ab4, ab5, ab23, ab24, ac3, ac8, ac24, ad13, ad18, ae2, ae25, af2, af25 gnd_cklk (9) w11 aa13 aa13 table 85. flex 10ke fineline bga device pin-outs (part 2 of 3) notes (1) , (2) pin name 484-pin fineline bga EPF10K130E epf10k200s 672-pin fineline bga EPF10K130E 672-pin fineline bga epf10k200e epf10k200s
altera corporation 117 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet no connect (n.c.) a3, a4, a5, a6, a8, a9, a10, a11, a12, a13, a14, a15, a16, a17, a18, a19, a20, a21, a22, a23, a24, b3, b4, b5, b6, b7, b8, b9, b10, b11, b12, b13, b14, b16, b19, b20, b21, b22, b23, b24, b26, c1, c25, c26, d1, d2, d25, d26, e1, e25, e26, f1, f25, g25, g26, h1, j1, j25, j26, k26, l2, l25, n2, p1, p2, r1, r26, t1, u1, u25, v1, v26, w1, y26, aa1, aa2, aa25, ab2, ab25, ab26, ac1, ac2, ac25, ac26, ad2, ad26, ae1, ae3, ae4, ae5, ae6, ae7, ae8, ae9, ae10, ae11, ae12, ae14, ae15, ae16, ae17, ae19, ae20, ae21, ae22, ae23, ae24, ae26, af3, af4, af5, af6, af7, af8, af9, af10, af11, af12, af13, af14, af15, af16, af17, af18, af20, af21, af23, af24 a4, a5, a6, a10, a11, a12, a13, a14, a15, a16, a17, a18, a19, a20, a21, a22, a23, a24, b4, b5, b6, b7, b8, b9, b10, b11, b12, b13, b16, b19, b20, b21, b22, b23, b24, c1, ae4, ae5, ae6, ae7, ae8, ae9, ae10, ae11, ae12, ae14, ae15, ae16, ae17, ae19, ae20, ae21, ae22, ae23, af4, af5, af6, af7, af8, af9, af10, af12, af13, af14, af15, af16, af18, af20, af21, af23, af24 total user i/o pins (12) 369 413 470 table 85. flex 10ke fineline bga device pin-outs (part 3 of 3) notes (1) , (2) pin name 484-pin fineline bga EPF10K130E epf10k200s 672-pin fineline bga EPF10K130E 672-pin fineline bga epf10k200e epf10k200s
118 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation notes to tables: (1) all pins that are not listed are user i/o pins. (2) all fineline bga packages support sameframe pin migration to allow migration from one package to another. the quartus and max+plus ii software perform s this function automatically when future migration is set. (3) this pin is a dedicated pin and i s not available as a user i/o pin. (4) this pin can be used as a user i/o pin if it is not used for its device-wide or configuration function. (5) this pin can be used as a user i/o pin after configuration. (6) this pin is tri-stated in user mode . (7) this pin drives the clocklock and clockboost circuitry. (8) this pin shows the status of the clocklock and clockboost circuitry. when the clocklock and clockboost circuitry is locked to the incoming clock and generates an internal clock, lock is driven high. lock remains high if a periodic clock stops clocking. the lock function is optional; if the lock output is not used, this pin is a user i/o pin. (9) this pin is the power or ground for the clocklock and clockboost circuitry. to ensure noise resistance, the power and ground supply to the clocklock and clockboost circuitry should be isolated from the power and ground to the rest of the device. if the clocklock or clockboost circuitry is not used, this power or ground pin should be connected to vccint or gnd, respectively . (10) when using the epf10k100b device, connect this pin to vccint . (11) when using the epf10k100b device, connect this pin to gndint . (12) the user i/o pin count includes dedicated input pins, dedicated clock pins, and all i/o pins. table 86 shows pin compatibility between different flex 10ke devices. notes: (1) all fineline bga packages support sameframe pin migration to allow migration from one package to another. the quartus and max+plus ii software automatically avoids conflicting pins when future migration is set. (2) devices in the same package are pin-compatible and have the same number of i/o pins. (3) devices in the same package are pin-compatible, although some devices have more i/o pins than others. when planning device migration, use the i/o pins that are common to all devices. the max+plus ii software versions 9.1 and higher provide features to help use only the common pins. (4) this option will be supported with a 484-pin fineline bga package. by using sameframe pin migration, all fineline bga packages are pin-compatible. for example, a board can be designed to support 256-pin, 484-pin, and 672-pin fineline bga packages. the quartus and max+plus ii software automatically avoids conflicting pins when future migration is set. table 86. flex 10ke device pin compatibility note (1) device 144-pin tqfp 208-pin pqfp 240-pin pqfp rqfp 599-pin pga 356-pin bga 600-pin bga 256-pin fineline bga 484-pin fineline bga 672-pin fineline bga epf10k30e (2) (2) (3) (3) (4) epf10k50e (2) (2) (3) (3) (3) (3) (4) epf10k50s (2) (2) (3) (3) (3) (3) (4) epf10k100b (2) (3) (3) epf10k100e (2) (3) (3) (3) (3) (4) EPF10K130E (3) (3) (3) (3) (3) epf10k200e (2) (3) (3) epf10k200s (3) (2) (3) (3) (3) (3)
altera corporation 119 preliminar y inf ormation flex 10ke embed ded pr ogrammab le logic f amil y data sheet table 87 shows the flex 10ke device/package combinations that support sameframe pin-outs for both flex 10ka and flex 10ke devices . all fineline bga packages support sameframe pin-outs , providing the flexibility to migrate not only from device to device within the same package, but also from one package to another. the i/o count will vary from device-to-device. therefore, the m ax+plus ii software versions 9.1 and higher provide features to help designers use only the common pins . f for more information, search for ?ameframe?in max+plus ii help. note: (1) this option will be supported with a 484-pin fineline bga package and sameframe migration. table 87. flex 10k & f lex 10ke sameframe pin-out support device 256-pin fineline bga 484-pin fineline bga 672-pin fineline bga epf10k30e v v v (1) epf10k50e epf10k50s v v v (1) epf10k100b v epf10k100e v v v (1) EPF10K130E v v epf10k200e epf10k200s v epf10k10a v epf10k30a v v epf10k50v v epf10k100a v
120 altera corporation flex 10ke embed ded pr ogrammab le logic f amil y data sheet preliminar y inf ormation revision histor y the information contained in the flex 10ke embedded programmable logic family data sheet version 2.02 supersedes information published in previous versions. v ersion 2.02 changes the flex 10ke embedded programmable logic family data sheet version 2.02 contains the following changes: n clocklock and clockboost parameters updated in tables 12 and 13 . n 2.5-v device operating conditions updated in tables 20 and 21 . n nceo pin note updated in tables 81 and 82 . n gndint and gndio pin-outs updated for epf10k200e and epf10k200s devices in 600-pin bga package in table 82 . v ersion 2.01 changes the flex 10ke embedded programmable logic family data sheet version 2.01 contains the following changes: n updated note (2) on page 50 . n corrected 356-pin bga package no connect pins for epf10k50e and epf10k50s devices in table 82 . n sylistic changes were made throughout the data sheet.
copyright ? 1995, 1996, 1997, 1998 , 1 9 9 9 altera corporation, 101 innovation drive, san jose, c a 95134, usa, all rights r eserved. by accessing this information, you ag r ee to be bound by the terms of alteras legal notice.

▲Up To Search▲

Price & Availability of EPF10K130E

	To Download EPF10K130E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .